Abstract:In this paper, the effect of thermomechanical treatment process on the hardening behavior, grain microstructure, precipitated phase, and tensile mechanical properties of the new high-strength and high-ductility Al-10.0Zn-3.0Mg-2.8Cu alloy was studied, and the optimal thermomechanical treatment process was established. The strengthening and toughening mechanisms were revealed, which provided technical and theoretical guidance for the engineering application of this kind of high strength-ductility aluminum alloy. Al-10.0Zn-3.0Mg-2.8Cu alloy cylindrical parts with external longitudinal reinforcement were prepared by a composite extrusion deformation process (reciprocal upsetting + counter-extrusion) with a true strain up to 2.56, and the organizational evolution of the alloys during the extrusion deformation process and the influence of pre-stretching treatments on the subsequent aging precipitation behaviors and mechanical properties were investigated. The results show that firstly, the large plastic deformation promotes the fragmentation of coarse insoluble phases and the occurrence of dynamic recrystallization, which results in the elongation of the grains along the extrusion direction, and the volume fraction of recrystallization reaches 42.4%. Secondly, the kinetic study showed that the decrease in the activation energy of precipitation increased the nucleation sites, which further promoted the diffuse distribution of the second phase in the alloy and a higher number of nucleation sites, while limiting the coarsening of the precipitated phase. When the amount of pre-deformation was increased from 0% to 2%, the size of the matrix precipitated phase decreased from 5.11 μm to 4.1 μm, and when the amount of pre-deformation was increased from 2% to 7%, the coarsening of the matrix precipitated phase took place, and the size of the phase increased from 4.1 μm to 7.24 μm. The finalized heat treatment process for the deformation of the aluminum alloy tailframe was as follows: solution (475 °C/3 h) + 2% pre-stretching + aging (120 °C/24 h), at which the comprehensive performance of the alloy was optimized, with a tensile strength of 634.2 MPa, a yield strength of 571.0 MPa, and an elongation of 15.2%. The alloy was strengthened by both precipitation strengthening and dislocation strengthening. After 2% pre-stretching, the fracture surface starts to be dominated by dense tough nest structure, and most of them are small tough nests, and small and dense tough nests are the main reason for the increase in alloy toughness after 2% pre-stretching deformation.

Preparation and deformation behaviour of multi-structural aluminium-coated steels

The Research on Al-Si Coating for Hot Forming Steel

Influence of Thermal Modification on Al-Si Coating of Hot-Stamped 22mnb5 Steel: Microstructure, Phase Transformation, and Mechanical Properties

Effect of Al-Si Coating on Weld Microstructure and Properties of 22mnb5 Steel Joints for Hot Stamping

Experimental Investigation of Hot Forming of Zn‐Coated Hot‐Stamping Steel

The Effect of a Coating Sprayed Using Supersonic Flame Coating Technology on the Mechanical Properties and Interface Structure of a Thick Steel/Aluminum Composite Plate during Hot Rolling

Achieving three-layered Al/Mg/Al sheet via combining porthole die co-extrusion and hot forging

Role of the pre-existed cracks in the high-cycle fatigue properties of the Al-Si coated press hardened steel

Integrating interfacial bonding and coordinated deformation in steel/Al bilayers via a pin-less friction stir-assisted synchronous joining-forming approach

Coordinated deformation mechanisms of high formability Al–Mg–Si–Cu–Zn–Fe alloys via coupling control of thermomechanical processes

Improving the performance of steel aluminum resistance spot welding joints based on steel coating design

Effect of Different Coatings on the Weldability of Al to Steel

Interfacial Microstructure and Mechanical Properties of Dissimilar Aluminum/steel Joint Fabricated Via Refilled Friction Stir Spot Welding

Research on high-temperature oxidation resistance, hot forming ability, and microstructure of Al–Si–Cu coating for 22MnB5 steel

Experimental Investigation and Kinetic Analysis of Al–Zn–Mg Alloy Coating

Effect of Hot Deformation and Heat Treatment on the Microstructure and Properties of Spray-Formed Al-Zn-Mg-Cu Alloys

Influence of hot forming on microstructure and mechanical properties of laser tailor-welded dissimilar ultra-high-strength steels

Investigation of the Compound Strength of Hybrid Casting Components with Different Variations of Coated and Undercut Sheet Metal

Study on the Aging Precipitation Behavior and Kinetics of Al-10.0Zn-3.0Mg-2.8Cu Alloy by Pre-Deformation Treatment

Research on Tribological Behavior and Mechanism of Laser Surface Texturing on Tool Surface in Hot Stamping of Al-Si-coated High-Strength Steel

Comprehensive Understanding of the Mechanical Properties and Microstructure Evolution of Aluminum Alloy/steel Laminates During Friction Stir-Assisted Incremental Forming with Synchronous Bonding Process