Abstract:In this study, three cationic surfactants (hexadecyltrimethylammonium chloride, hexadecyldimethylbenzylammonium chloride, and octadecyltrimethylammonium chloride) were used to modify montmorillonite and polyethylene (PE)/maleic anhydride grafted polyethylene (PE-g-MAH)/organic-montmorillonite (Org-MMT) nano-composites, prepared by two blending processes (direct-melt blending and solution blending). X-ray diffractometry and transmission electron microscopy were used to investigate the intercalation behavior and microstructure of composites. Mechanical properties were also tested. It was found that the intercalation effect of PE/PE-g-MAH/Org-MMT could be enhanced by increasing the content of PE-g-MMT, using the silicate modified by a cationic surfactant with a benzyl group or long alkyl chain, adopting the solution-blending method or using high-density polyethylene as matrix. The degree of crystallinity of composites and the crystalline thickness perpendicular to the crystalline plane [like (110) and (200)] decreased with increasing amounts of PE-g-MAH and, under certain prescription, the crystalline thickness of the composite made by the solution method was much smaller than that made by direct-melt blending. This clearly showed that Org-MMT and PE-g-MAH had a heterogeneous nucleation effect on crystallization of PE from the melt, resulting in a decrease of crystalline thickness, and the heterogeneous nucleation effect was more evident in the nanocomposite made by the solution-blending method than in that made by the direct-melt intercalation process. The tensile strength initially increased and then decreased with increasing contents of PE-g-MAH. The maximum value in tensile strength (23.3 MPa) was achieved when the concentration of PE-g-MAH was 6 wt %. The impact strength increased concomitantly with the content of PE-g-MAH; it was 122.2 J/m when the concentration of PE-g-MAH was 9 wt %. (C) 2004 Wiley Periodicals, Inc.

Effect of injection molding on structure and properties of poly(styrene‐ethylene‐butylene‐styrene) and its nanocomposite with functionalized montmorillonite

In-situ Synthesis, Thermal and Mechanical Properties of Biobased Poly(ethylene 2,5-Furandicarboxylate)/montmorillonite (PEF/MMT) Nanocomposites

Preparation and structure of poly(styrene-acrylonitrile)/montmorillonite nanocomposite

Polyethylene/maleic Anhydride Grafted Polyethylene/organic‐montmorillonite Nanocomposites. I. Preparation, Microstructure, and Mechanical Properties

Preparation by Direct Injection and Properties of Polypropylene/Montmorillonite Composites

Preparation and characterization of poly(propylene carbonate)/montmorillonite nanocomposites by solution intercalation

Preparation of Poly(Phenylene Oxide)/Polyamide-6 Nanocomposites with High Tensile Strength and Excellent Impact Performance

Preparation and characterization of poly(styrene-<i>b</i>-butadiene-<i>b</i>-styrene)/montmorillonite nanocomposites

Preparation and characterization of poly(styrene‐b‐butadiene‐b‐styrene)/montmorillonite nanocomposites

Effect of compound organification of montmorillonite on the structure and properties of polypropylene/montmorillonite nanocomposites

Investigation Into Poly(propylene)/Montmorillonite/Calcium Carbonate Nanocomposites

A New Method Combining Modification of Montmorillonite and Crystal Regulation to Enhance the Mechanical Properties of Polypropylene

Influence of the injection molding process on the mechanical properties of (PA6/GF/MMT) nanocomposite

The morphology evolution and crystallization behavior of microinjection molded polyoxymethylene/molybdenum disulfide nanocomposite

Key interactions in biodegradable thermoplastic starch/poly(vinyl alcohol)/montmorillonite micro- and nanocomposites

Rheological and extrusion behavior of intercalated high-impact polystyrene/organomontmorillonite nanocomposites

Morphology, Thermal and Mechanical Properties of Poly (Styrene-Acrylonitrile) (SAN)/Clay Nanocomposites from Organic-Modified Montmorillonite

Effect of Processing Conditions on the Mechanical Properties of Microcellular Injection Molded Polyethersulfone

Effect of Multi-Monomer Grafted Polyolefin Elastomer/Polypropylene on the Structure and Properties of Polypropylene/Montmorillonite Nanocomposites

Study on the dynamic self-organization of montmorillonite in two phases

Injection molding and shear‐induced stress simulation of poly (styrene‐ethylene‐butylene‐styrene) and polypropylene blends