Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Elasticity, mechanical and thermal properties of submicron h-AlN: in-situ high pressure ultrasonic study

First-Principle Calculations of Elastic Properties of Wurtzite-Type Aluminum Nitride under Pressure

Ab Initio Studies On Phase Transition, Thermoelastic, Superconducting And Thermodynamic Properties Of The Compressed Cubic Phase Of Alh3

The first-principles calculations for the elastic properties of Zr2Al under compression

High pressure sintering behavior and mechanical properties of cBN-Ti 3Al and cBN-Ti 3Al-Al composite materials

Novel High-Pressure Phases of AlN: A First-Principles Study

Acoustic velocities, elasticity, and pressure-induced elastic softening in compressed neodymium

Theoretical investigation of the elastic, electronic, thermodynamic and optical properties of the zinc-blende structure AlN under high pressure

Thermoelastic and Texture Behavior of Aluminum at High Pressure and High Temperature Investigated by in Situ Neutron Diffraction

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

Novel High-Pressure Phases of Alp from First Principles

First-principles Study of Ni-Al Intermetallic Compounds under Various Temperature and Pressure

Theoretical study of the elastic and thermodynamic properties of Pt$_{3}$Al with the L1$_{2}$ structure under high pressure

Sound velocities, elasticity and thermal properties of cBN composite with AlN binder at high pressure

Experimental and DFT Investigations of AlNbTiVZr High Entropy Alloys with Excellent Mechanical Properties

Formation and properties of rocksalt-type AlN and implications for high pressure phase relations in the system Si–Al–O–N

Size-Induced Reduction of Transition Pressure and Enhancement of Bulk Modulus of AlN Nanocrystals

Study of the Mechanical and Thermodynamic Properties on NiAl and Ni3Al

Sound Velocities, Elasticity, and Mechanical Properties of Stoichiometric Submicron Polycrystalline δ-MoN at High Pressure

Thermal conductivity of crystalline AlN and the influence of atomic-scale defects

Study on the uniaxial tensile mechanical behavior of two-dimensional single-crystal aluminum nitride