Abstract:<p>The aim of the present paper is to evaluate the effect of Lode angle incorporation into a fracture criterion when predicting the ballistic resistance of 2024-T351 aluminum alloy plates struck by cylindrical projectiles with different nose shapes through finite element (FE) simulations. To this end ballistic tests in the sub-ordnance impact velocity range were firstly conducted on 9.94 mm thick 2024-T351 aluminum alloy plates using cylindrical projectiles with blunt, hemispherical and ogival nose shapes, a nominal diameter of 12.66 mm, and a nominal mass of 50 g. Ballistic limit velocities (BLVs) for different projectile-target pairs considered were calculated using initial vs. residual velocity data obtained in the experiments. Subsequently FE simulations of the conducted experiments were performed with SIMULIA Abaqus software. In those simulations Johnson-Cook yield criterion with a modified strain hardening law was accompanied with either the Lode-independent Johnson-Cook (JC) fracture criterion or the Lode-dependent modified Mohr-Coulomb (MMC) fracture criterion to describe target material properties. Finally, the predicted ballistic resistance and fracture patterns of the targets were compared with those observed in the experiments. It was found that in the simulations with the Lode-independent JC fracture criterion the BLVs of the targets were overestimated by 18.0-35.1% depending on the projectile nose shape. In the simulations with MMC fracture criterion the BLVs predictions were substantially improved, so that the difference with the experimental results did not exceed 9.0%. Targets failure mechanisms obtained in the simulations with MMC fracture criterion also better match the experiments than those predicted with JC fracture criterion. In the simulations with MMC fracture criterion the targets impacted by the projectiles with blunt and hemispherical noses failed through shear plugging, whereas ogive-nosed projectiles caused ductile hole enlargement and target fragmentation due to its rear side radial fracture and bending of formed short petals with their eventual shear fracture. At the same time the simulations with JC fracture criterion predicted shear plugging for the blunt-nosed projectiles, very small conical plug ejection and target fragmentation due to discing for the hemispherical-nosed projectiles, and ductile hole enlargement for the ogive-nosed projectiles. A detailed analysis of the failure process revealed that in the case of the ogive-nosed and hemispherical-nosed projectiles, respectively, the ductile hole enlargement occurs during the initial stage of the impact and subsequent through-thickness fracture develops causing either fragmentation of the target or its shear plugging failure. The Lode-independent JC fracture criterion overestimates a material fracture strain under shear, thus leading to poor prediction of 2024-T351 aluminum alloy targets ballistic performance in the numerical simulations.</p>

A comment on "Plasticity, ductile fracture and ballistic impact behavior of Ti-6Al-4V Alloy" by Wu et al. (2023), Int. J. Impact Eng. 174:104493

Numerical Study on the Perforation of Steel Plates by Multiple Projectiles

Experimental and Numerical Investigation on Ballistic Penetration Performance of TC4-Al3Ti Layered Composites by Hot Rolling

Numerical simulation of the disk fragment impacting resistance of plate target

Ballistic testing and theoretical analysis for perforation mechanism of the fan casing and fragmentation of the released blade

Experimental and numerical investigation on the ballistic resistance of 2024-T351 aluminum alloy plates with various thicknesses struck by blunt projectiles

Experimental and numerical investigation on the ballistic resistance of ZK61m magnesium alloy plates struck by blunt and ogival projectiles

Application of the modified Mohr–Coulomb fracture criterion in predicting the ballistic resistance of 2024-T351 aluminum alloy plates impacted by blunt projectiles

Multiple ballistic impacts of thin metallic plates: Numerical simulation

Experimental and numerical study on the ballistic resistance of 6061-T651 aluminum alloy thin plates struck by different nose shapes of projectiles

Impact Crushing and Rebound of Thin-Walled Hollow Spheres

Brittleness and micro damage evolution analysis of target impacted by projectile

The constitutive behavior of Ti–5Al–3V–2Cr–2Fe under high-velocity impact: Experimental, modeling, and validation

Effect of Lode angle incorporation into a fracture criterion in predicting the ballistic resistance of 2024-T351 aluminum alloy plates struck by cylindrical projectiles with different nose shapes

Experimental and Numerical Study on the Ballistic Resistance of Heterogeneous Double-Layered Aluminum Alloy Targets Against Blunt Projectiles

Numerical investigation on dynamic damage behavior of a novel N-shaped perforated armor plate under ballistic impact

Experimental-numerical study on ballistic impact behavior of 316L austenitic stainless steel plates against blunt and ogival projectiles

Computational modelling of impact damage in brittle materials

Constitutive Behavior and Ballistic Performance of Aerospace 2A16 Aluminum Alloy under Different Impact Velocities

Nonlinear analysis model of the progressive damage of aluminum–wood sandwich structures under high-speed impact conditions

Influence of impact velocity on impact-initiated reaction behavior of Zr-Ti-Nb alloy