Abstract:<p>The aim of the present paper is to evaluate the effect of Lode angle incorporation into a fracture criterion when predicting the ballistic resistance of 2024-T351 aluminum alloy plates struck by cylindrical projectiles with different nose shapes through finite element (FE) simulations. To this end ballistic tests in the sub-ordnance impact velocity range were firstly conducted on 9.94 mm thick 2024-T351 aluminum alloy plates using cylindrical projectiles with blunt, hemispherical and ogival nose shapes, a nominal diameter of 12.66 mm, and a nominal mass of 50 g. Ballistic limit velocities (BLVs) for different projectile-target pairs considered were calculated using initial vs. residual velocity data obtained in the experiments. Subsequently FE simulations of the conducted experiments were performed with SIMULIA Abaqus software. In those simulations Johnson-Cook yield criterion with a modified strain hardening law was accompanied with either the Lode-independent Johnson-Cook (JC) fracture criterion or the Lode-dependent modified Mohr-Coulomb (MMC) fracture criterion to describe target material properties. Finally, the predicted ballistic resistance and fracture patterns of the targets were compared with those observed in the experiments. It was found that in the simulations with the Lode-independent JC fracture criterion the BLVs of the targets were overestimated by 18.0-35.1% depending on the projectile nose shape. In the simulations with MMC fracture criterion the BLVs predictions were substantially improved, so that the difference with the experimental results did not exceed 9.0%. Targets failure mechanisms obtained in the simulations with MMC fracture criterion also better match the experiments than those predicted with JC fracture criterion. In the simulations with MMC fracture criterion the targets impacted by the projectiles with blunt and hemispherical noses failed through shear plugging, whereas ogive-nosed projectiles caused ductile hole enlargement and target fragmentation due to its rear side radial fracture and bending of formed short petals with their eventual shear fracture. At the same time the simulations with JC fracture criterion predicted shear plugging for the blunt-nosed projectiles, very small conical plug ejection and target fragmentation due to discing for the hemispherical-nosed projectiles, and ductile hole enlargement for the ogive-nosed projectiles. A detailed analysis of the failure process revealed that in the case of the ogive-nosed and hemispherical-nosed projectiles, respectively, the ductile hole enlargement occurs during the initial stage of the impact and subsequent through-thickness fracture develops causing either fragmentation of the target or its shear plugging failure. The Lode-independent JC fracture criterion overestimates a material fracture strain under shear, thus leading to poor prediction of 2024-T351 aluminum alloy targets ballistic performance in the numerical simulations.</p>

Experimental and Numerical Study on the Ballistic Resistance of Heterogeneous Double-Layered Aluminum Alloy Targets Against Blunt Projectiles

Experimental and Numerical Investigation on Ballistic Penetration Performance of TC4-Al3Ti Layered Composites by Hot Rolling

Experimental and numerical investigation on the ballistic resistance of 2024-T351 aluminum alloy plates with various thicknesses struck by blunt projectiles

Experimental and numerical investigation on the anti-penetration performance of metallic sandwich plates for marine applications

Numerical Study on the Perforation of Steel Plates by Multiple Projectiles

Effects of Target Thickness and Macroscopic Interface on the Ballistic Performance of Ti6Al4V Titanium Alloy

Effect of Lode angle incorporation into a fracture criterion in predicting the ballistic resistance of 2024-T351 aluminum alloy plates struck by cylindrical projectiles with different nose shapes

Effect of incorporating Lode angle parameter into a fracture criterion in predicting ballistic impact behavior of double-layered 2024-T351 aluminum alloy plates against blunt projectiles

Simulation of ballistic performance of a two-layered structure of nanostructured metal and ceramic

Experimental and numerical study on the ballistic resistance of 6061-T651 aluminum alloy thin plates struck by different nose shapes of projectiles

Effect of Lode angle and projectile diameter on the ballistic resistance of 6061-T651 aluminum alloy plates struck by hemispherical nosed projectile

Application of the modified Mohr–Coulomb fracture criterion in predicting the ballistic resistance of 2024-T351 aluminum alloy plates impacted by blunt projectiles

The Limit Velocity and Limit Displacement of Nanotwin-Strengthened Metals under Ballistic Impact

Constitutive Behavior and Ballistic Performance of Aerospace 2A16 Aluminum Alloy under Different Impact Velocities

Evaluation of the Impact Resistance of Steel–Aluminum Laminated Target Plates with Isoplanar Density

Effect of projectile diameter on ballistic resistance and failure mechanism of single and layered aluminum plates

Dynamic Mechanical Properties and Modification of Fracture Criteria of 6061-T651 Aluminum Alloy

Ballistic performance and mechanism of B 4 C/Al laminated targets with different configurations

Experimental investigation on the ballistic resistance of monolithic and multi-layered plates against hemispherical-nosed projectiles impact

Dynamic failure behavior of 7B52 laminated aluminum alloy subjected to deformable projectile impact

Experimental and Numerical Investigation on the Perforation Resistance of Double-Layered Metal Shield under High-Velocity Impact of Armor-Piercing Projectiles