Abstract:Vapor deposition of perovskite solar cells (PSCs) has attracted considerable interest for its dry processing characteristics. However, a two-step sequential vapor deposition method suffers from ineffective conversion of PbI2 to perovskite with reasons still unclear. In this report, we carefully investigated the crystallization orientation of PbI2 films deposited by physical vapor deposition via synchrotron grazing-incidence wide-angle X-ray scattering (GIWAXS) and observed an asymmetric scattering pattern with respect to the qz-axis. The observed oriented morphology and texture hinder the diffusion of MAI molecules in the PbI2 films synthesized by vapor deposition, resulting in over 15% PbI2 remaining at the buried interface after reaction with MAI vapor. As a result, the MAPbI3 synthesized in this way was also highly oriented, especially in the surface layers. Surface fumigation (SF) step was introduced to decrease the orientational anisotropy of PbI2, which successfully breaks the diffusion barriers of MAI molecules by forming a complex layer on the PbI2 surface with polar solvent vapors, like dimethyl sulfoxide or 1,3-dimethyl-2-imidazolidinone. We infer that the SF treatment changes the vapor–solid reaction mechanism from reaction–crystallization to dissolution–recrystallization, which largely promotes the conversion of PbI2 to perovskite. Defects were reduced in perovskite synthesized in this way, and a p-i-n device with 19.56% efficiency was fabricated, which is among the highest efficiencies reported for sequential-vapor-deposited PSCs. Notably, this method enables the fabrication of conformal perovskite layers on uneven substrates. An exemplary PSC showing efficiency of 8.93% was fabricated on a precurved substrate. We believe that the method is applicable to the fabrication of tandem or curved PSCs that are compatible with wearable or building/autocar-integrated photovoltaics in the future.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c12283.XRD, SEM, GIWAXS, coordination rate test, diagram of saturated vapor pressure, stability of different complexes, MAI loss rate, film color changes during the reaction, comparison of the efficiency, J–V curves, steady-state output at the maximum power point, the corresponding external quantum efficiency (EQE) spectra in the literature (PDF)This article has not yet been cited by other publications.

Binary Additive Engineering Enables Efficient Perovskite Solar Cells via Spray-Coating in Air

High Efficiency over 20% of Perovskite Solar Cells by Spray Coating via a Simple Process

Synergetic Effect on Enhanced Photovoltaic Performance of Spray-Coated Perovskite Solar Cells Enabled by Additive Doping and Antisolvent Additive Spraying Treatment

Additive Engineering in Spray Enables Efficient Methylammonium-Free Wide-Bandgap Perovskite Solar Cells

Progress in Spray Coated Perovskite Films for Solar Cell Applications

One-Step Spray-Coated All-Inorganic CsPbI 2 Br Perovskite Solar Cells

Fully Spray-Coated Perovskite Solar Minimodules via a Vacuum-Flash Assisted Solution Process

Optimization of spray coating for the fabrication of sequentially deposited planar perovskite solar cells

Hexamethylphosphoramide-Assisted Structure and Morphology Regulation of a PbI2 Film for Air-Processed Efficient Perovskite Solar Cells Via a Two-Step Deposition Method

Printable CsPbI3 Perovskite Solar Cells with PCE of 19% via an Additive Strategy

Generic Water-Based Spray-Assisted Growth for Scalable High-Efficiency Carbon-Electrode All-Inorganic Perovskite Solar Cells

Simple Method of Dual Passivation with Efficiency Beyond 20% for Fabricating Perovskite Solar Cells in the Full Ambient Air

A Scalable Electrodeposition Route to the Low-Cost, Versatile and Controllable Fabrication of Perovskite Solar Cells

Co-solvent strategy for highly efficient perovskite solar cells by spray coating

Enhanced Efficiency and Stability of Scalable Spray-coated Perovskite Solar Cells with Ionic liquid Additives

Efficient inorganic perovskite solar cells made by drop-coating in ambient air

Enhanced efficiency of planar perovskite solar cells via a two-step deposition using DMF as an additive to optimize the crystal growth behavior

Surface-Orientation Elimination of Vapor-Deposited PbI 2 Flakes for Efficient Perovskite Synthesis on Curved Solar Cells

Perovskite solar cells based on screen-printed thin films

“Coffee ring” controlment in spray prepared >19% efficiency Cs0.19FA0.81PbI2.5Br0.5 perovskite solar cells

Ultrahigh Fill-Factor All-Inorganic CsPbBr3 Perovskite Solar Cells Processed from Two-Step Solution Method and Solvent Additive Strategy