Abstract:The frictional behaviors of implant soft materials in vivo are important to medical effect. In this study, hydroxyethyl acrylate sodium/acryloyldimethyl taurate copolymer (EMT-10) aqueous dispersions are adopted, acting as lubricants in hydrophobic polydimethylsiloxane elastomer (PDMS) Gemini interfaces or hydrophilic polyamide hydrogel (PAM) Gemini interfaces, respectively. The associations exist in EMT-10 aqueous dispersions via hydrogen bonding, electrostatic and hydrophobic interactions, similar to bio-lubricants. The EMT-10 aqueous dispersions, surface characteristics of Gemini interfaces and the axial force (N-a) during frictional experiments in Stribeck curves are studied. Under low and high concentrations of EMT-10 lubricant, the PDMS Gemini interfaces exhibit opposing sensitivity to N-a, different from the PAM Gemini interfaces, which always showing lower CoF at higher N-a. This phenomenon results from the various degree of perfection for lubrication film between the Gemini interfaces. To further distinguish the lubrication film formation, and correlate frictional surface characteristic and rheological behaviors of lubricant, a new parameter, relative thickness (phi), is established. When phi<1, the lubrication film is discrete, and the boundary lubrication regime plays dominant role during the frictional test. When phi>1, the entire lubrication film forms and the whole system enters hydrodynamic lubrication regime. For PDMS Gemini interfaces, the lubrication film is composed of the confined and adsorbed EMT-10 polymer chains owing to the strong attraction between the hydrophobic surface and the C-C backbone. As a result, the lubrication film is greatly affected by the concentration of the lubricant thus phi increases. The PDMS frictional system gradually converts from the boundary into hydrodynamic lubrication regime. For PAM Gemini interfaces, the film is made of the hydrogel surface mesh and the confined EMT-10 chains, so phi is always larger than 1, exhibiting the characteristic of hydrodynamic lubrication regime. The study tends to probe the frictional behavior of the complex fluids in the soft Gemini interfaces and unveils the mechanism behind the phenomenon. [GRAPHICS] .

Optimum Design of Coaxial Hydraulic Sealing Systems Made from Polytetrafluoroethylene and Its Compounds

Tribological Behavior of Hydraulic Cylinder Coaxial Sealing Systems Made from PTFE and PTFE Compounds

Theoretical and Experimental Research Concerning the Friction Forces Developed in Hydraulic Cylinder Coaxial Sealing Systems Made from Polymers

Analysis on dynamic experimental system of lubrication film properties of friction pairs in axial piston pump

Numerical Analysis of the Traction Effect on Reciprocating Seals in the Hydraulic Actuator

Tolerance Design Guideline for Piston/cylinder Interface of Electro-Hydrostatic Actuator (EHA) Pumps Based on a Thermal-Fluid-Structure Model

Computational Analysis of Sealing and Stability of a Deformable Floating and Fixed Rings of an Annular Seal

Design and FEM Analysis of Plastic Parts of a Tie-Rod Composite Hydraulic Cylinder

Design and Optimization of Self-Compensation Oil Distributor for Hydraulic Motors

Material Analysis and Molecular Dynamics Simulation for Cavitation Erosion and Corrosion Suppression in Water Hydraulic Valves

Friction behavior of rough polydimethylsiloxane surfaces under hydrophobic polymer aqueous solution conditions

Overview of Materials Used for the Basic Elements of Hydraulic Actuators and Sealing Systems and Their Surfaces Modification Methods

Experimental investigation on frictional behavior and sealing performance of different composites for seal application

A New Elastic Non Contacting Sealing Concept for Valves

Studies on the Lubrication Between Hydrophilic-Hydrophilic/Hydrophobic-Hydrophobic Gemini Interfaces and Complex Fluids

Significantly Reducing Friction and Wear of Water‐Based Fluids with Shear Thinning Bicomponent Supramolecular Hydrogels

EXPERIMENTAL STUDY OF MOTION-RESISTANCE FORCE OF HYDRAULIC CYLINDER OF CRHDM

Optimum Design of Spiral Grooved Mechanical Seal Based on Thermo-Hydrodynamics

Elastohydrodynamic lubrication and finite configuration changes in reciprocating elastomeric seals

Optimization design for mechanical seals in reactor coolant pumps based on a fluid-solid strong-interaction model

A Novel Hybrid Seal: Design and Experimental Validation on a High Pressure Rotordynamic Test Rig