Abstract:Non-equiatomic high entropy alloys (HEAs) and medium entropy alloys (MEAs) are expected to have the potential to exhibit good mechanical properties due to abundant composition designs compared to equiatomic alloys. It has been reported that an equiatomic CoCrNi MEA shows better strength-ductility balance than CoCrFeMnNi HEA, and there is a possibility that the mechanical properties can be further improved by changing chemical composition. Among the constituent elements, cobalt (Co) has the effect of decreasing stacking fault energy (SFE). In this study, we clarified the effect of Co-content on mechanical properties of non-equiatomic Co–Cr–Ni MEAs with different amounts of Co through investigating deformation behaviors and deformation microstructures. Cox(CrNi)(100−x) (x = 20 (Co20), 40 (Co40), 60 (Co60) at%) MEAs were processed to very high plastic strains by high-pressure torsion (HPT) and subsequently annealed under proper conditions to obtain FCC single-phase and uniform fine grain sizes. Mechanical properties of the specimens with fully recrystallized microstructures were characterized by tensile tests at room temperature. Their deformed microstructures at different tensile strain levels were observed by electron microscopy. The result of the tensile tests showed that the work-hardening rate was enhanced with increasing the Co-content although early fracture before reaching plastic instability condition occurred in Co60. Planar slip of dislocations and deformation twinning were observed in Co20 (SFE = 30 mJ/m2), while, in addition to them, deformation-induced martensitic transformation to HCP ε-martensite was observed in Co40 having lower SFE (SFE = 10 mJ/m2), leading to higher work-hardening rate. By increasing Co-content (decreasing SFE) further, phase fraction of ε-martensite greatly increased in Co60 (SFE = 0 mJ/m2) compared with Co40, and early fracture occurred due to stress concentration at intersects between martensite and grain boundaries. The present results suggested that the mechanical properties of the present materials could be effectively designed by controlling the SFE.

First-principle study on physical properties and vacancy formation of face-centered cubic Co-Ni-Cu-Mo-W high entropy alloys

Vacancy dependent mechanical behaviors of high-entropy alloy

Chemical environment and magnetic moment effects on point defect formations in CoCrNi-based concentrated solid-solution alloys

Effect of Mo Content on Microstructure and Mechanical Properties of CoCrFeNi Series High-entropy Alloys

Exploring thermophysical properties of CoCrFeNiCu high entropy alloy via molecular dynamics simulations

First-principles study on the structure, fracture toughness, and thermodynamic properties of a new-designed Co30Ni30 Fe20Cr20 high-entropy alloy

Mechanical properties and fracture mechanism of as-cast MnFeCoCuNi high-entropy alloys

First-principle study of interstitial atoms (C, B and Si) in CrFeCoNi high entropy alloy

Effects of Al and La elements on mechanical properties of CoNiFe0.6Cr0.6 high-entropy alloys: a first-principles study

Engineering defect energy landscape of CoCrFeNi high-entropy alloys by the introduction of additional dopants

First‐Principles Calculations for the Enhancement of Mechanical Properties of High‐Entropy Alloys by Carbon Elements

Microstructural evolution and mechanical properties of FeCoCrNiCu high entropy alloys: a microstructure-based constitutive model and a molecular dynamics simulation study

Improved mechanical properties of Co-free high-entropy Cantor alloy: A first-principles study

Enhancing the mechanical properties of casting eutectic high-entropy alloys via W addition

Dynamic deformation behaviors and mechanisms of CoCrFeNi high-entropy alloys

Molecular dynamics simulations of tensile response for FeNiCrCoCu high-entropy alloy with voids

First principles prediction of yield strength of body centered cubic structured high entropy alloys

Effect of Cobalt-Content on Mechanical Properties of Non-Equiatomic Co–Cr–Ni Medium Entropy Alloys

Ab Initio Investigation of High-Entropy Alloys of 3d Elements

The Magnetic, Electronic, and Thermodynamic Properties of High Entropy Alloy CrMnFeCoNi: A First‐Principles Study

High-Entropy Materials Design by Integrating the First-Principles Calculations and Machine Learning: A Case Study in the Al-Co-Cr-Fe-Ni System