Abstract:Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, Ahead of Print. Cranial defects are often caused by trauma, diseases or malignancy. To repair such defects, skull reconstruction or cranial implants are required for protecting intracranial structures and normalizing cerebral hemodynamics. To relieve Intracranial Pressure (ICP) surgeons restore cranial defects using the preserved bone of a patient. In case of non-availability of natural bone cranial implants are fabricated using biocompatible materials including Titanium Alloys (Ti-6Al-4V) and polyether-ether-ketone (PEEK). Patient-specific implants (PSI) manufactured using 3D printing, 3D imaging technologies and 3D modeling software, are preferred over conventional manufacturing methods. During cranial fixation bone fragments, grafts and bone flaps are fixed to the cranium to offer stable closure in surgery. Effective attachment of an implant to a defective skull is influenced by the joints and fixture arrangements at the interface. These fixtures can have various designs, materials and joining procedures. PEEK behaves similarly to bone during deformation, which means it is receptive to titanium fixations and supports soft tissue adhesion due to its inert nature. This study considers PEEK as an implant material for reconstructing a bone-defected skull with Ti-6Al-4V fixtures attached at the skull-implant interface. This work compares Ti-6Al-4V fixture shapes (Linear, Square and Burrhole) with different orientation angles and topologies ('+' and 'X') attached to PEEK cranial implants of variable thicknesses (1–7 mm). Using Finite Element Method (FEM)/Finite Element Analysis (FEA), von Mises stress analysis was analyzed to identify the implant thicknesses that would bear an external load of 1780 N and ICP of 15 mmHg without failure. With a yielding limit of 100 MPa for PEEK, all proposed design arrangements for the fixture plates in the skull-implant assembly were well within these limits exhibiting a maximum von Mises stress of 51.985 MPa for the least implant thickness of 1 mm and weight 12.90 g. Considering all the designs, a Linear Fixture shape with 45° angular orientations placed in 'X' topology exhibited least stress of 18.477 MPa and was therefore proposed as the most optimized design for the skull-implant fixture assembly. Selection of an optimized design arrangement is also dependent upon other clinical factors, such as number of screws used, the Additive Manufacturing (AM) technique for fabricating/cutting of precise slots within the implant. The skull and flexibility of the fixture plates are also considered in relation to the required operating theatre time and skills of the surgical team.

Extrusion‐Based Additive Manufacturing of Cranial Implants Using High‐Performance Polymers: A Comparative Study on Mechanical Performance and Dimensional Accuracy

Biofunctional Glycol-Modified Polyethylene Terephthalate and Thermoplastic Polyurethane Implants by Extrusion-Based Additive Manufacturing for Medical 3D Maxillofacial Defect Reconstruction

Powder Bed Fusion Versus Material Extrusion: A Comparative Case Study on Polyether-Ether-Ketone Cranial Implants

Polyether-Ether-Ketone (PEEK) and Its 3D-Printed Quantitate Assessment in Cranial Reconstruction

Optimization and manufacture of polyetheretherketone patient specific cranial implants by material extrusion - A clinical perspective

Quantitative Assessment of Point-of-Care 3D-Printed Patient-Specific Polyetheretherketone (PEEK) Cranial Implants

Patient-Specific Surgical Implants Made of 3D Printed PEEK: Material, Technology, and Scope of Surgical Application

Advanced 3D Printing of Polyetherketoneketone Hydroxyapatite Composites via Fused Filament Fabrication with Increased Interlayer Connection

An In Vitro Study of Osteoblast Response on Fused-Filament Fabrication 3D Printed PEEK for Dental and Cranio-Maxillofacial Implants

Additively manufactured polyether ether ketone (PEEK) skull implant as an alternative to titanium mesh in cranioplasty

Point-of-Care 3-Dimensional–Printed Polyetheretherketone Customized Implants for Cranioplastic Surgery of Large Skull Defects

The Direct 3D Printing of Functional PEEK/Hydroxyapatite Composites via a Fused Filament Fabrication Approach

Designing cranial fixture shapes and topologies for optimizing PEEK implant thickness in cranioplasty

Mechanical characterization of biocompatible PEEK by FDM

The microstructural evolution of material extrusion based additive manufacturing of polyetheretherketone under different printing conditions and application in a spinal implant

Comparison of 3D-printed poly-ether-ether-ketone and traditional implant materials in cranioplasty

The Effects of Structural & Materials Design on the Mechanisms of Tissue Integration with the 3D Printed Polyether-Ether-Ketone Cranial Implants in Vivo

The Mechanical, Thermal, and Biological Properties of Materials Intended for Dental Implants: A Comparison of Three Types of Poly(aryl-ether-ketones) (PEEK and PEKK)

3D Printed Strontium and Zinc Doped Hydroxyapatite Loaded PEEK for Craniomaxillofacial Implants

Material extrusion of thermoplastic acrylic for intraoral devices: Technical feasibility and evaluation

Carbon Fiber Reinforced PEEK Composites Based on 3D-Printing Technology for Orthopedic and Dental Applications