Abstract:Polyether ether ketone (PEEK) is introduced as a material for the additive manufacturing process called fused filament fabrication (FFF), as opposed to selective laser sintering (SLS) manufacturing. FFF manufacturing has several advantages over SLS manufacturing, including lower initial machine purchases costs, ease of use (spool of filament material vs powder material), reduced risk of material contamination and/or degradation, and safety for the users of the equipment. PEEK is an excellent candidate for FFF due to its low moisture absorption as opposed to other common FFF materials, such as Acrylonitrile Butadiene Styrene (ABS). PEEK has been processed into a filament and samples have been manufactured using several build orientations and extrusion paths. The samples were used to conduct tensile, compression, flexural, and impact testing to determine mechanical strength characteristics such as yield strength, modulus of elasticity, ultimate tensile strength and maximum elongation, etc. All tests were conducted at room temperature. A microscope analysis was also conducted to show features on the failures surfaces. The mechanical property results from this study are compared to other published results using traditional thermo-plastic manufacturing techniques, such injection molding. Tensile testing was conducted at three raster orientations, 0°, 90° and alternating between 0° and 90°. Average ultimate tensile stresses were determined to be 73 MPa for 0° orientation, and 54 MPa for 90° orientation, with alternating 0°/90° orientations of 66.5 MPa. Compression testing was conducted at two raster orientations, 0° and alternating between 0° and 90°. Average ultimate strength for the single orientation direction was 80.9 MPa with the alternating orientations at 72.8 MPa. Flexural testing was conducted at three raster orientations, 0°, 90° and alternating between 0° and 90°. Ultimate flexural stress was determined to be 111.7 MPa for 0°, 79.7 MPa for 90°, and 95.3 MPa for orientations alternating between 0° and 90°. Finally, impact testing was conducted at three raster orientations, 0°, 90° and alternating between 0° and 90°. Average impact energy absorbed was determined to be 17.5 Nm in the 0° orientation, 1.4 Nm in the 90° orientation, and 0.7 Nm for the alternating 0° and 90° orientations.

Mechanical characterization of biocompatible PEEK by FDM

Effects of processing parameters and annealing on the mechanical properties of polyether ether ketone(PEEK) via fused deposition modeling(FDM)

Mechanical Properties of Additively Manufactured PEEK Components Using Fused Filament Fabrication

Experimental Investigation on the Mechanical and Dynamic Thermomechanical Properties of Polyether Ether Ketone Based on Fused Deposition Modeling

Effect of 3D Printing Process Parameters and Heat Treatment Conditions on the Mechanical Properties and Microstructure of PEEK Parts

Carbon Fiber Reinforced PEEK Composites Based on 3D-Printing Technology for Orthopedic and Dental Applications

Enhancing the mechanical properties of SCF/PEEK composites in FDM via process-parameter optimization

Mechanical characterization of PEEK-CF/PEEK sandwich structures prepared via a combination of fused filament fabrication and epoxy post-bonding

Research on the Fused Deposition Modeling of Polyether Ether Ketone

Effect of process parameters of fused deposition modeling on mechanical properties of poly-ether-ether-ketone and carbon fiber/poly-ether-ether-ketone

Effects of FDM parameters and annealing on the mechanical and tribological properties of PEEK

Taguchi-Based Experimental Investigation and Modeling of 3D-Printed PEEK Parts as Biomedical Implants using Fused Deposition Modeling for Improving Mechanical Strength and Surface Quality

PEEK for Oral Applications: Recent Advances in Mechanical and Adhesive Properties

In-house processing of 3D printable polyetheretherketone (PEEK) filaments and the effect of fused deposition modeling parameters on 3D-printed PEEK structures

Mechanical performance of PEEK-Ti6Al4V interpenetrating phase composites fabricated by powder bed fusion and vacuum infiltration targeting large and load-bearing implants

Influence of Thermal Processing Conditions on Mechanical and Material Properties of 3D Printed Thin-Structures Using PEEK Material

Effect of Heat Treatment on Elastic Properties and Fracture Toughness of Fused Filament Fabricated PEEK for Biomedical Applications

Tensile and Bending Strength Improvements in PEEK Parts Using Fused Deposition Modelling 3D Printing Considering Multi-Factor Coupling

Improved design of fused deposition modeling equipment for 3D printing of high-performance PEEK parts

Extrusion‐Based Additive Manufacturing of Cranial Implants Using High‐Performance Polymers: A Comparative Study on Mechanical Performance and Dimensional Accuracy

Optimizing process parameters of fused deposition molding for 3D printing customized control of polyetheretherketone scaffolds