Abstract:Filamentation has extensively been explored and is well understood at repetition rates <1 kHz due to the typical availability of multi-mJ laser systems at a moderate average power. The advent of high-power Yb-lasers opened new possibilities for filamentation research. However, so far, high average power Yb systems have mostly been explored to increase the driving pulse energy to several hundreds of mJ and not at significantly higher repetition rates. In this paper, we study, for the first time, long filaments at unprecedented high repetition rates of 10, 40, and 100 kHz using a 500-W Yb-doped thin-disk amplifier driver operating with sub-700 fs pulses. We compare the filament length, density hole, and fluorescence at a constant peak power but different repetition rates and find a strong dependence on filament length and density depletion with repetition rate. Our analysis reveals the emergence of a significant stationary density depletion at repetition rates of 40 and 100 kHz. The corresponding reduction in the breakdown threshold by increasing the laser repetition rate observed in our study signifies a promising avenue for enhancing the efficiency and reliability of electric discharge triggering in various scenarios. Using capacitive plasma probe measurements, we address the limitations of fluorescence imaging-based measurements and demonstrate a systematic underestimation of filament length. This work contributes to a deeper understanding of the interplay between laser repetition rates, filamentation, and heat-driven density depletion effects from high-repetition-rate high-power laser systems and will contribute to guiding future research, making use of filaments at high repetition rates.

High efficiency laser ablation of gold thin film by 2.8 GHz intraburst repetition rate pulses

High efficiency femtosecond laser ablation with gigahertz level bursts

Femtosecond time-resolved pump-probe measurements on percolating gold in the ablation regime

Ablation-cooled material removal with ultrafast bursts of pulses

An Atomic-Level Study of Material Ablation and Spallation in Ultrafast Laser Processing of Gold Films

High-repetition-rate, High-Peak-power Burst Mode Laser with YAG/Nd:YAG/Cr4+:YAG Composite Crystal

72-Kw High-Peak-power Linearly-Polarized Single-Mode Pulsed Fiber Laser with 80 Khz Repetition Rate and 4.5 Ns Duration

Case study on the dynamics of ultrafast laser heating and ablation of gold thin films by ultrafast pump-probe reflectometry and ellipsometry

An efficient high-power femtosecond laser based on periodic-layered-Kerr media nonlinear compression and a Yb:YAG regenerative amplifier

High Efficiency 878.6nm LD End-Pumped Pulse Burst Nd:YVO4 Laser

Novel ultrafast laser ablation by bibursts in the MHz and GHz pulse repetition rates

Thin-disk multi-pass amplifier for kilowatt-class ultrafast lasers

Ultrafast Dynamics of Laser Thermal Excitation in Gold Film Triggered by Temporally Shaped Double Pulses

High Repetition-Rate Laser Diode Side-Pumped Burst-Mode Nd:YAG Laser with Enhanced Output Pulse Uniformity

High-Peak-Power, High-Repetition-Rate Ld End-Pumped Nd:Yvo4 Burst Mode Laser

A 2.2J All-Diode-pumped Nd:YAG Burst-Mode Laser at Repetition Rate of 10Khz

83 W, 3.1 MHz, square-shaped, 1 ns-pulsed all-fiber-integrated laser for micromachining

High-power sub-picosecond filamentation at 1.03 μm with high repetition rates between 10 and 100 kHz

μS Pulsed, Low Repetition Rate, 30 W Fiber Laser at 1550 nm

High Peak Power Actively Q-switched Mid-Infrared Fiber Lasers at 3 Μm

Laser Performance of High Repetition Frequency on a 970 Nm LD Side-Pumped Er:YSGG Crystal Operated at 2.79 Μm