Abstract:In the industry, chrome coating is an important player in the functional layer application. Due to its high corrosion and wear resistance as well as high hardness [1], hard chrome plating is a popular choice in the automotive and aerospace industry. However, since September 2017, the application of chrome (VI) in surface treatment is banned by the European Chemical Agency (ECHA) due to chrome (VI) being toxic and environmentally hazardous [2]. Chrome (III) compound is a popular substitute for chrome (VI) due to it being less toxic compared to chrome (VI). However, chrome (III) coating has a lower corrosion resistance, and the electroplating process is more sensitive to metallic impurities. Many new innovations have since been developed such as the plasma electrolytic oxidation (PEO), extreme highspeed laser deposition (EHLA). Even established technologies such as physical vapour deposition (PVD), thermal spraying and case hardening process have tried to replace hard chrome coating with a degree of success. Admittedly, the above-mentioned technologies have their fair share of disadvantages. PEO, a green procedure [3], causes a metal substrate to develop a highly resistant oxide which is extremely strong and corrosion as well as wear resistant. The process however needs a high temperature and pressure, continuous replacement of electrolytes and consumes a great amount of power which made the process not feasible for a wide industrial application [4-6]. EHLA and thermal spraying on the other hand are restricted to rotational symmetric components. PVD is restricted to substrates that can handle high processing temperature like nitrable ferrous base materials. Lastly, case hardening processes requires long heat treatments which contribute to a higher process cost. [7] In our presentation, another alternative for chrome coating based on electrodeposition will be introduced. The element tungsten is considered in our experiments because tungsten not only has an excellent corrosion properties and high tensile strength at high temperature, but it also has a microhardness of 650 Vickers. However, it is not possible to deposit tungsten from an aqueous solution because tungstate cannot be directly reduced to metallic tungsten due to a very low overvoltage for hydrogen evolution on tungsten. Thus, an induced co-deposition mechanism is needed, and it is known that tungsten can be easily codeposited with iron group metal. [8-9] In this study a modified Watt's bath is used as electrolyte to deposit NiW alloy. Our preliminary tests have shown that tungsten can also be deposited with nickel without the help of citric acid as complexing agent. The usage of citric acid does indeed inhibit the deposition of nickel but show no influence in the deposition of tungsten. Hence, in our study, experiments with the rotating disc electrode (RDE) will be done to see if tungsten content in the coating could be increased when the hydrodynamic and coating parameters are manipulated. The chemical composition of the layer is measured using SEM/EDX and the surface morphology is pictured using SEM. Metallographic cross-sections are made to see if there are any fissures in the layer and the hardness of the layer is measured using the microhardness test. The dependency of hardness on the tungsten content in the layer and the annealing parameter will also be shown in the presentation. XRD measurement is conducted for phase analysis and grain size calculation. Figure 1

The effect of distance variation on electroplating process of decorative nickel-chrome on the microstructure, thickness and weight of plating on A36 steel

Pengaruh Arus Dan Waktu pelapisan hard chrome terhadap ketebalan lapisan dan tingkat kekerasan mikro pada plat baja karbon rendah aisi 1026 dengan menggunakan cro3 250 gr/lt dan h2so4 2,5 gr/lt pada proses elektroplating

Effect of hard chrome plating parameters on the wear resistance of low carbon steel

Electroplating and Physicochemical Properties of Zinc–Nickel Alloy Coatings from Ammonium Oxalate Electrolytes

Development Method for Nickel Electroplating on Aluminium

A Method for Electroless Nickel Plating on Aluminum Alloy Surface

STUDY OF ELECTROLESS NICKEL PLATING ON RAPID PROTOTYPING MODEL USING ACRYLONITRILE BUTADIENE STYRENE

Electrodeposition of Ni-W Alloy from Citric Acid Free Aqueous Electrolyte As a Substitute for Hard Chrome Coating and the Effect of Tungsten Content on Coating Hardness

Optimization of the Preparation Parameters of High-Strength Nickel Layers by Electrodeposition on Mild Steel Substrates

Novel Electroless Nickel Plating Process

Optimization of Black Nickel Coatings’ Electrodeposit onto Steel

The Effect of Various Surface Treatments in Cleaning and Preparing Copper, Nickel and Steel for Chromium Plating

Optimizing Nickel Electroplating in Low-Ni Environments for Efficient Source Production in Small Plating Baths

The Performance of Zn-Ni Alloy Coating Electrodeposited from Stabilized Bath

Effects of deposition current density, time and scanning velocity on scanning jet electrodeposition of Ni-Co alloy coating

An analytical investigation pertaining to autocatalytic plating of chromium nickel carbide powder on copper alloys using electroless deposition method

Comparison of Different Surface Pre-Treatment on Mild Steel for Cobalt-Nickel-Iron Electroplating

Electroplating Behavior of Zn-Ni Alloys in an Alkaline Electrolyte

Surface Finishing and Coating Parameters Impact on Additively Manufactured Binder-Jetted Steel–Bronze Composites

Electrodeposition and Characterization of Nano-Structured Black Nickel Thin Films

Main Directions of the Electrochemical Chrome Plating Process Intensification