Abstract:In this paper, the effect of thermomechanical treatment process on the hardening behavior, grain microstructure, precipitated phase, and tensile mechanical properties of the new high-strength and high-ductility Al-10.0Zn-3.0Mg-2.8Cu alloy was studied, and the optimal thermomechanical treatment process was established. The strengthening and toughening mechanisms were revealed, which provided technical and theoretical guidance for the engineering application of this kind of high strength-ductility aluminum alloy. Al-10.0Zn-3.0Mg-2.8Cu alloy cylindrical parts with external longitudinal reinforcement were prepared by a composite extrusion deformation process (reciprocal upsetting + counter-extrusion) with a true strain up to 2.56, and the organizational evolution of the alloys during the extrusion deformation process and the influence of pre-stretching treatments on the subsequent aging precipitation behaviors and mechanical properties were investigated. The results show that firstly, the large plastic deformation promotes the fragmentation of coarse insoluble phases and the occurrence of dynamic recrystallization, which results in the elongation of the grains along the extrusion direction, and the volume fraction of recrystallization reaches 42.4%. Secondly, the kinetic study showed that the decrease in the activation energy of precipitation increased the nucleation sites, which further promoted the diffuse distribution of the second phase in the alloy and a higher number of nucleation sites, while limiting the coarsening of the precipitated phase. When the amount of pre-deformation was increased from 0% to 2%, the size of the matrix precipitated phase decreased from 5.11 μm to 4.1 μm, and when the amount of pre-deformation was increased from 2% to 7%, the coarsening of the matrix precipitated phase took place, and the size of the phase increased from 4.1 μm to 7.24 μm. The finalized heat treatment process for the deformation of the aluminum alloy tailframe was as follows: solution (475 °C/3 h) + 2% pre-stretching + aging (120 °C/24 h), at which the comprehensive performance of the alloy was optimized, with a tensile strength of 634.2 MPa, a yield strength of 571.0 MPa, and an elongation of 15.2%. The alloy was strengthened by both precipitation strengthening and dislocation strengthening. After 2% pre-stretching, the fracture surface starts to be dominated by dense tough nest structure, and most of them are small tough nests, and small and dense tough nests are the main reason for the increase in alloy toughness after 2% pre-stretching deformation.

Effect of storage time on the surface status and resistance spot weldability of TiZr pretreated 5182 aluminum alloy

Effect of surface treatments and storage conditions on resistance spot weldability of aluminum alloy 5182

Interesting Phenomena for Al-Zn-Mg Aluminum Alloy after Two Years of Storage: A Comparative Study on Microstructure, Mechanical Properties and Corrosion Behavior of Aluminum Alloy with Different Aging Treatments

The effect of partial substitution of Zr for Ti on the electrochemical properties and surface passivation film of Mg35Ti10 - xZrxNi55 (x=1, 3, 5, 7, 9) electrode alloys

Effect of non-isothermal aging treatments on the microstructure and properties of TiC-TiB2 ceramic particles-reinforced spray-formed 7055 aluminum alloy TIG weld metal

An Impact of Zirconium Doping of Zn-Al Braze on the Aluminum-Stainless Steel Joints Integrity During Aging

Effect of Al Content on the Long-Term Corrosion Behavior of Arc-Sprayed ZnAl Alloy Coatings

Effect of Filler Wire on Mechanical Properties, Microstructure and Natural Aging Behavior of 2A55 Al-Li Alloy TIG Welded Joint

Effect of heat treatment on the microstructure and mechanical properties of spray formed 7055 aluminum alloy TIG welded joints reinforced by ZrB 2 / Al 3 (Sc, Zr) particles

Study on the Aging Precipitation Behavior and Kinetics of Al-10.0Zn-3.0Mg-2.8Cu Alloy by Pre-Deformation Treatment

Effect of Aging Time on the Microstructural Characterization and Corrosion Resistance of Al-4.5Cu-1Li-0.4Mg-0.4Ag-0.4Mn-0.5Zn Alloys

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Extruded Al–4Cu–1Li–0.4Mg–0.4Ag–0.18Zr Alloy

Effect of ultrasonic impact time on microstructure and properties of 7A52 aluminum alloy tandem MIG welded joint

Effects of aging treatment on the precipitation behaviors and mechanical properties of Al-5.0Mg-3.0Zn-1.0Cu cast alloys

Effect of Voltage and Time on Microstructure and Corrosion Resistance of Anodic Oxidation Film on Al-5.5Zn-0.03In-1Mg-0.03Ti-0.08Sn Alloy

Research on the Post-Weld Heat Treatment of TIG Repair Welded Joint of Sand-Cast Mg-Y-RE-Zr Alloy

Effects of TiZn3 and TiZn16 Components on the Microstructure and Mechanical Performance of Ti-6Al-4 V Alloy Joints Formed Via Ultrasonic Assisted Brazing Using Pre-Galvanized Workpieces.

Effect of Variable Rate Non-isothermal Aging on the Microstructure and Properties of Al-Zn-Mg-Cu Alloy

Influence of Aging Treatment on the Microstructure, Mechanical Properties and Corrosion Behavior of Al-Zn-Mg-Sc-Zr Alloy

Influence of Zr addition on TIG welding-brazing of Ti-6Al-4V toAl5A06

Study on Corrosion Resistance of Zr-702 Zirconium Plate TIG Welded Joint in Sulfuric Acid Environment