Abstract:Copper as well as copper base composites reinforced with coated and uncoated 1 wt% diamond, graphite particles or short carbon fibers are prepared by powder metallurgy process. The reinforcement particles were encapsulated with silver as well as copper layer by using the electroless deposition technique to investigate the influence of the reinforcement surface coating on the microstructure, density, electrical and thermal properties of the sintered samples. The coated and the uncoated powders were cold compacted at 600 MPa, and then sintered at 1173 K (900°C) for 2 h under hydrogen atmosphere. The phase composition, morphology and microstructure of the prepared powders as well as the copper base sintered composites were investigated using X-ray diffraction analysis (XRD) and Scanning Electron Microscope (SEM) equipped with an Energy Dispersive Spectrometer (EDS) respectively. The density of the sintered composites was measured by Archimedes method. The copper base consolidated composites had a density up to 96% and the reinforcement coated particles were distributed uniformly within the copper matrix better than the uncoated one. The electrical resistivity at room temperature and the heat transfer conduction of the produced samples were measured in a temperature range between 323 K (50°C) and 393 K (120°C). The results observed that the sintered materials prepared from the coated powder have lower electrical resistivity than the sintered materials prepared from the mixed powders. On the other hand the thermal conductivity values were calculated using the heat transfer conduction values by means of the Fourier formula. The results observed that the thermal conductivity of copper is (391 W/m·K), 1 wt% diamond/Cu is (408 W/m·K), 1 wt% graphite coated silver/Cu is (393 W/m·K), 1 wt% Cu coated short carbon fiber/Cu is (393 W/m·K), graphite/Cu is (383 W/m·K) and short carbon fiber/Cu is (382 W/m·K). The obtained composites are expected to be suitable for heat sink applications. The heat transfer testing experiments were done. The forced convection of the present work was done and compared with the previous work in the literature, and satisfactory agreement was achieved.

Microstructure and wear characterization of Al2O3 reinforced silver coated copper matrix composites by electroless plating and hot pressing methods

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Processing copper and silver matrix composites by electroless plating and hot pressing

Microstructural, mechanical and wear behavior of electroless assisted silver coated Al2O3–Cu nanocomposites

Microstructural, Mechanical, and Tribological Characteristics of Ceramic Reinforced Al/Cu Hybrid Matrix Composites

Effect of the Thermal Expansion Characteristics of Reinforcements on the Electrical Wear Performance of Copper Matrix Composite

Investigation of the Microstructure and Mechanical Properties of Copper-Graphite Composites Reinforced with Single-Crystal α-Al2O3 Fibres by Hot Isostatic Pressing

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

The wear and microstructural characterization of copper surface coated with TiC reinforced FeAl intermetallic composite by ESD method

Microstructure, wear and corrosion properties of Cu–SiC/WCCo composite coatings on the Cu substrate surface by plasma spray method

Study on Metallurgically Prepared Copper-Coated Carbon Fibers Reinforced Aluminum Matrix Composites

Enhanced mechanical and tribological properties of copper matrix composites reinforced by copper-coated graphite and Ti3AlC2

Effect of Copper-Plated Graphite Content on the Microstructure and Properties of Copper-Graphite Composites Prepared by Spark Plasma Sintering

Microstructure, mechanical and tribological properties of Cu-Sn/Cr3C2/Gr composites

Fabrication, Microstructure, Thermal and Electrical Properties of Copper Heat Sink Composites

Investigating the tribological characteristics of copper surface composites reinforced with high entropy alloy (AlCoCrCuFe) through friction stir processing

Powder Metallurgical Processing of Al–5 wt% Cu Matrix Composites Reinforced with MoSi2 and WSi2 Particulates

Synthesis and Characterization of Titanium Carbide and/or Alumina Nanoparticle Reinforced Copper Matrix Composites by Spark Plasma Sintering

Tribological Aspects, Optimization and Analysis of Cu-B-CrC Composites Fabricated by Powder Metallurgy

High-temperature mechanical and electrical properties of W-particle-reinforced Cu-matrix composites from improved electroless plated powders

Microstructure and properties of plasma sprayed copper-matrix composite coatings with Ti3SiC2 addition