Abstract:Tungsten carbide (WC), celebrated for its exceptional strength, hardness, and chemical inertness, serves as an exemplary reinforcement for copper (Cu) matrix composite (CMC) coatings, significantly enhancing their wear and corrosion resistance. However, the inherent poor wettability and interfacial bonding between WC and Cu during the cold spray additive manufacturing process pose challenges to further performance improvement of these coatings. This study investigates cold-sprayed CMC coatings reinforced with WC particles, both with and without an electroless plated cobalt (Co) shell (Co@WC; at 10 wt.% and 20 wt.%), focusing on their microstructure, mechanical properties, tribological behavior, and electrochemical corrosion resistance. The findings indicate a reduction in CMC coatings` porosity and mean free path (MFP) of reinforcement particles with increasing reinforcement content. Despite slight Co shell damage during deposition, ceramic retention is notably enhanced, reaching up to 149.3%. The microhardness and wear resistance of CMC coating are improved with decreased MFP and increased ceramic content. Compared to the Cu coating, the microhardness of CMC coatings escalates by up to 32.9% (151.8HV0.1), and the specific wear rate is dramatically reduced by up to 84.2%. The Co shell effectively prevents the detachment of Co@WC particles, thereby enhancing the bending and wear resistance. Electrochemical corrosion tests, encompassing open circuit potential (EOCP), polarization curve, and electrochemical impedance spectroscopy (EIS), indicate that lower porosity, high ceramic content and the Co shell substantially boost the corrosion resistance of the CMC coating. Specifically, the coating with 20 wt.% Co@WC (Cu20(Co@WC)) demonstrates superior corrosion resistance compared to the Cu coating, hinting at the potential for further enhancement with increased ceramic content.

The wear and microstructural characterization of copper surface coated with TiC reinforced FeAl intermetallic composite by ESD method

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Enhanced mechanical and tribological properties of copper matrix composites reinforced by copper-coated graphite and Ti3AlC2

Influence of TiC Addition on Corrosion and Tribocorrosion Resistance of Cr2Ti-NiAl Electrospark Coatings

Study on the Tribology Properties of the Particles/Cu Composite Coatings

Ceramic-metal Composite Coating on Steel Using a Powder Compact Tool Electrode by the Electro-Discharge Coating Process

Microstructure and high-temperature wear properties of in situ TiC composite coatings by plasma transferred arc surface alloying on gray cast iron

Microstructure and wear resistance of in-situ TiC reinforced Stellite 6 coating using PTA cladding

Development of Al-Ni-TiC Composite Coating on Commercially Pure Al Using Tungsten Inert Gas Welding Route and its Wear Behavior

Microstructure and wear characterization of Al2O3 reinforced silver coated copper matrix composites by electroless plating and hot pressing methods

Microstructure, wear and corrosion properties of Cu–SiC/WCCo composite coatings on the Cu substrate surface by plasma spray method

CORROSION, WEAR AND MECHANICAL PROPERTIES OF LAMINATED Al/TiC COMPOSITES

Effect of Copper on Microstructure and Performance of WC/NiAl/TiC Composite Coatings by Laser Cladding

Microstructure and tribological behavior of Al-TiC composite strips fabricated by a multi-step densification method

Pulsed Electrode Surfacing of Steel with TiC Coating: Microstructure and Wear Properties

Study on the Properties of TiC Coating Deposited by Spark Discharge on the Surface of AlFeCoCrNiCu High-Entropy Alloy

Microstructure and properties of TiB2/Cu composite coating with multi-layer structure prepared by electrodeposition

Structural, Electrical and Corrosion Properties of Bulk Ti–Cu Alloys Produced by Mechanical Alloying and Powder Metallurgy

Enhancing microhardness and surface integrity of Ti–6Al–4V alloy using WC–Cu composite electrode aided electrical discharge coating

Study Of Wear And Corrosion Resistances Of Ni60-Wc + Tic Composite Coating

The effect of advanced electrodeposited Ni-P-Cu coatings obtained with scrap cu plates on the tribological performance of Al powder metallurgy products