Abstract:It is known that Copper's (Cu) electrical conductivity makes it a desirable material for use in industry. Due to poor properties such as hardness, thermal expansion, and corrosion resistance, its applications are limited. This manuscript solves these problems while maintaining no breakdown in electrical conductivity. In this study, high-strength ceramics (SiC nanoparticles and graphene nanosheets) were used as reinforcements in the manufacture of Cu-based hybrid nanocomposites using powder metallurgy technique. X-ray diffraction analysis (XRD) was used to investigate phase composition and crystal size of the milled powders. Transmission electron microscopy (TEM) and field emission scanning electron microscopy (FESEM), respectively examined the microstructure of the prepared powder powders and sintered nanocomposites. Then, various properties of the sintered samples are measured, including physical, electrical and thermal properties and wear resistance. The obtained XRD technique and TEM images showed decreases in the crystal and particle size of milled samples reaching up to 14.08 and 28.30 nm, respectively for the sample contained 8 vol. % SiC + 0.8 vol. % graphene (SG8). A surprising improvement in the mechanical properties of up to 809.15, 341.84 MPa and 336.56 GPa for microhardness, strength and longitudinal modulus for the sample containing the highest reinforcements, achieving an improvement of up to 122, 61.37 and 41 percent compared to the Cu matrix. Moreover, there was a noticeable improvement in the coefficient of thermal expansion (CTE) and wear rate values of the samples by increasing the percentages of hybrid reinforcements in the examined sintered nanocomposite samples. The Sample SG8 recorded the lowest value, decreasing by about 50.2 and 76.5% compared to the SG1 sample. Finally, adding reinforcements to the Cu matrix had a negative effect on the relative density and electrical conductivity, and the lowest values was 92.94% and8.59 × 10 6 S/m, respectively for the SG sample.

Synthesis and Characterization of Titanium Carbide and/or Alumina Nanoparticle Reinforced Copper Matrix Composites by Spark Plasma Sintering

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

Evaluation of tribo-mechanical measurements and thermal expansion of Cu-based nanocomposites reinforced by high strength hybrid ceramics

Spark Plasma Sintering of Copper Matrix Composites Reinforced with TiB2 Particles

Sintering Densification of Cu/Al2O3p Nano-Composite Powders by Electroless Copper Plating

Enhancement of Electrical Conductivity of Aluminum-Based Nanocomposite Produced by Spark Plasma Sintering

Experimental investigation on fabrication, characterization and properties of spark plasma sintered alumina-based tungsten carbide composites reinforced by carbon nanotubes

Influence of Nano-Hybrid Reinforcements on the Improvement Strength, Thermal Expansion and Wear Properties of Cu–SiC–Fly Ash Nanocomposites Prepared by Powder Metallurgy

Microstructure and Mechanical Properties of Composites Obtained by Spark Plasma Sintering of Ti3SiC2-15 vol.%Cu Mixtures

Spark Plasma Sintering of Cu-Ti-Ni Ternary Alloy: Microstructural, Thermal and Electrical Properties

Investigation on microstructure and properties of TiC0.5-Al2O3/Cu composites fabricated by a novel in-situ reactive synthesis

Enhancement of ultimate tensile strength and ductility of copper matrix composites using a low content of single-wall carbon nanotubes

Optimisation of Properties of Ti3SiC2 Reinforced Copper Matrix Composites

Study of Microstructural and Mechanical Properties of Al/SiC/TiO2 Hybrid Nanocomposites Developed by Microwave Sintering

Enhanced physical and mechanical properties of Cu-based nanocomposites with bundled multi-layered carbon nanotubes incorporation: fabrication and comparative analysis via conventional sintering and SPS techniques

Improving comprehensive performance of copper matrix composite by spray pyrolysis fabricated CNT/W reinforcement

Microstructural, Mechanical, and Tribological Characteristics of Ceramic Reinforced Al/Cu Hybrid Matrix Composites

Chemical synthesis, characterization and spark plasma sintering of cu and Cu/TiO2 composite powders

A Study On The Effects Of Hybrid (Sic- Pssa) Nano Sized Reinforcement On Mechanical And Tribological Behaviour Of Al Alloy-Based Metal Matrix Composite Produced By Ultrasonic Assisted Stir Casting

Preparation of in situ TiC@TiN core–shell and Ti2N–Al4C3 nanoparticles and their effects on Al–Zn–Mg–Cu alloy

Enhanced Electrical and Mechanical Properties of Alumina-Based Tic Composites by Spark Plasma Sintering