Abstract:Purpose Photon counting CT (PCCT) holds promise for mitigating metal artifacts and can produce virtual mono‐energetic images (VMI), while maintaining temporal resolution, making it a valuable tool for characterizing the heart. This study aimed to evaluate and optimize PCCT for cardiac imaging in patients during left ventricular assistance device (LVAD) therapy by conducting an in‐depth objective assessment of metal artifacts and visual grading. Methods Various scan and reconstruction settings were tested on a phantom and further evaluated on a patient acquisition to identify the optimal protocol settings. The phantom comprised an empty thoracic cavity, supplemented with heart and lungs from a cadaveric lamb. The heart was implanted with an LVAD (HeartMate 3) and iodine contrast. Scans were performed on a PCCT (NAEOTOM Alpha, Siemens Healthcare). Metal artifacts were assessed by three objective methods: Hounsfield units (HU)/SD measurements (DiffHU and SDARTIFACT), Fourier analysis (AmplitudeLowFreq), and depicted LVAD volume in the images (BloomVol). Radiologists graded metal artifacts and the diagnostic interpretability in the LVAD lumen, cardiac tissue, lung tissue, and spinal cord using a 5‐point rating scale. Regression and correlation analysis were conducted to determine the assessment method most closely associated with acquisition and reconstruction parameters, as well as the objective method demonstrating the highest correlation with visual grading. Results Due to blooming artifacts, the LVAD volume fluctuated between 27.0 and 92.7 cm3. This variance was primarily influenced by kVp, kernel, keV, and iMAR (R2 = 0.989). Radiologists favored pacemaker iMAR, 3 mm slice thickness, and T3D keV and kernel Bv56f for minimal metal artifacts in cardiac tissue assessment, and 110 keV and Qr40f for lung tissue interpretation. The model adequacy for DiffHU SDARTIFACT, AmplitueLowFreq, and BloomVol was 0.28, 0.76, 0.29, and 0.99 respectively for phantom data, and 0.95, 0.98, 1.00, and 0.99 for in‐vivo data. For in‐vivo data, the correlation between visual grading (VGSUM) and DiffHU SDARTIFACT, AmplitueLowFreq, and BloomVol was −0.16, −0.01, −0.48, and −0.40 respectively. Conclusion We found that optimal scan settings for LVAD imaging involved using 120 kVp and IQ level 80. Employing T3D with pacemaker iMAR, the sharpest allowed vascular kernel (Bv56f), and VMI at 110 keV with kernel Qr40 yields images suitable for cardiac imaging during LVAD‐therapy. Volumetric measurements of the LVAD for determination of the extent of blooming artifacts was shown to be the best objective method to assess metal artifacts.

Three-dimensional assessment of susceptibility-induced signal voids caused by active cardiac implants in the setting of 3.0T CMR

Magnetic Resonance Multitasking for Multidimensional Assessment of Cardiovascular System: Development and Feasibility Study on the Thoracic Aorta

Clinical safety of cardiac resynchronization therapy and implantable cardiac defibrillator implantation compatible with magnetic resonance imaging

3 Tesla magnetic resonance imaging in patients with cardiac implantable electronic devices: a single centre experience

Magnetic Resonance Myocardial Imaging in Patients With Implantable Cardiac Devices: Challenges, Techniques, and Clinical Applications

Evaluation of a compact 3 T MRI scanner for patients with implanted devices

Electrophysiological cardiovascular MR: procedure-ready mesh model generation for interventional guidance based on non-selective excitation compressed sensing whole heart imaging

Metal artefact reduction sequences for a piezoelectric bone conduction implant using a realistic head phantom in MRI

Development and evaluation of a numerical simulation approach to predict metal artifacts from passive implants in MRI

Optimization of photon counting CT for cardiac imaging in patients with left ventricular assist devices: An in‐depth assessment of metal artifacts

Comprehensive review of artifacts in cardiac MRI and their mitigation

Reconstruction and completion of high-resolution 3D cardiac shapes using anisotropic CMRI segmentations and continuous implicit neural representations

Building a comprehensive cardiovascular magnetic resonance exam on a commercial 0.55 T system: A pictorial essay on potential applications

Myocardial Characterization with Extracellular Volume Mapping with a First-Generation Photon-counting Detector CT with MRI Reference

Cardiothoracic and Vascular Surgery Implant Compatibility With Ultrahigh Field Magnetic Resonance Imaging (4.7 Tesla and 7 Tesla)

Dual stack black blood carotid artery CMR at 3T: application to wall thickness visualization

Susceptibility-weighted cardiovascular magnetic resonance in comparison to T2 and T2 star imaging for detection of intramyocardial hemorrhage following acute myocardial infarction at 3 Tesla

Safety of Magnetic Resonance Imaging in Patients with Cardiac Implantable Electronic Devices

Evaluation of 3D Multi-Contrast Joint Intra- and Extracranial Vessel Wall Cardiovascular Magnetic Resonance

A Comparison of Alternative Approaches to MR Cardiac Triggering: A Pilot Study at 3 Tesla