Abstract:Li2MnO3 stabilizes the structure of Li M O2 ( M = Mn, Ni, Co, etc.) and makes Li-rich layer-structured xLi2MnO3·(1-x)Li M O2 (0<x<1.0, M = Mn, Ni, Co, etc.) composites (or solid solutions) become potential cathode materials for high energy density lithium ion batteries. However, as Mn4+ is inactive in Li2MnO3, the charge compensation from O2- ions during the initial delithiation and the irreversible layer-to-spinel structural transition in the subsequent lithiation makes the composite suffer from drawbacks such as low initial coulombic efficiency, discharge voltage and energy density falling, and poor rate performance during cycling as well as safety hazard in the initial cycle. Although surface modification, atomic substitution and optimization of synthesis strategies have been pursued to improve the performances of the xLi2MnO3·(1-x)Li M O2 composites, the inherent drawbacks of Li2MnO3 component have not been, and cannot, overcome. Here we introduce Li2MoO3 with disordered NaFeO2 structure (R-3m) as a prospective alternation of Li2MnO3 for designing novel Li-rich cathode materials xLi2 M ´O3·(1-x)Li M O2. In this report, the structural transition and charge compensation of Li2MoO3 during the initial charge and discharge were investigated with STEM and synchrotron in situ XRD and XAS techniques. It is shown that, during the initial delithiation, solid-solution reaction and two-phase reaction (slipped O3 → faulted O1) go in series due to charge compensation from Mo4+ ions in both the Mo-O and Mo-Mo covalent bonds in the Mo3O13 cluster accompanied with the Mo ion migration from Li-2Mo layer to Li layer. In the subsequent lithiation, its structure is recovered to a Li-insufficient O3 type Li2-x MoO3 (x = 0.50) due to the incomplete reduction of Mo6+ ions and the nearly reversible migration of the Mo ions at the end of lithiation. Unlike the irreversible oxygen release in deeply delithiated Li2MnO3, the O K-edge soft XAS of Li2MoO3 illustrates that oxidation of O2- to O(2-σ )- is nearly reversible and is required dynamically rather than thermodynamically. These features make Li2MoO3 a promising superior alternate in constructing novel Li-rich cathode material with improved structural stability and easy charge compensation. In addition, the contribution of Mo-Mo covalent bond seems to help to maintain the framework of the electrode material by hindering the loss of oxygen. Therefore, the basic findings in this work will also bring new insight on understanding the performance decay and searching for new ways to improve the performance of the conventional xLi2MnO3·(1-x)Li M O2materials. Acknowledgements This work was financially supported by the National Natural Science Foundation (No. 51372268) of China and the National 973 Program of China (2009CB 220100). The work at Brookhaven National Lab. was supported by the U.S. Department of Energy, the Assistant Secretary for Energy Efficiency and Renewable Energy, Office of Vehicle Technologies under Contract No. DEAC02-98CH10886.

Zero Voltage‐Degradation of Li2MnO3 with Ultrathin Amorphous Li─Mn─O Coating

In-situ formation of Li0.5Mn0.5O coating layer through defect controlling for high performance Li-rich manganese-based cathode material

A Li-rich Layered Oxide Cathode with Negligible Voltage Decay

Structural Origin of Suppressed Voltage Decay in Single‐Crystalline Li‐Rich Layered Li[Li0.2Ni0.2Mn0.6]O2 Cathodes

High‐Voltage Spinel and Li2MnO3 Composite Structure Construction in LiMn0.8Ni0.2O2 for Manganese‐Based Lithium‐Ion Battery Cathode Materials

Long-cycle-life Li2MnO3 thin-film cathode enabled by all-solid-state battery configuration

Suppressing Voltage Decay in O2-Type Li-Rich Layered Cathode Materials through Microstrain Alleviation

Electrochemically Inert Li2MnO3: The Key to Improving the Cycling Stability of Li-Rich Manganese Oxide Used in Lithium-Ion Batteries

Structural Transition and Charge Compensation During the Initial Delithiation and Lithiation of Li2MoO3

High-energy 'composite' Layered Manganese-Rich Cathode Materials Via Controlling Li2MnO3 Phase Activation for Lithium-Ion Batteries.

Enhancing the Stability of Li-Rich Mn-Based Oxide Cathodes Through Surface High-Entropy Strategy

Amorphous Li2ZrO3 nanoparticles coating Li[Li0·17Mn0·58Ni0.25]O2 cathode material for enhanced rate and cyclic performance in lithium ion storage

Li‐Rich Li[Li1/6Fe1/6Ni1/6Mn1/2]O2 (LFNMO) Cathodes: Atomic Scale Insight on the Mechanisms of Cycling Decay and of the Improvement Due to Cobalt Phosphate Surface Modification

Improved electrochemical performance of layered Li1.2Ni0.13Co0.13Mn0.54O2 cathode material via VPO5 coating

Significant Enhancement of the Capacity and Cycling Stability of Lithium-Rich Manganese-Based Layered Cathode Materials via Molybdenum Surface Modification

A Novel Strategy to Suppress Capacity and Voltage Fading of Li‐ and Mn‐Rich Layered Oxide Cathode Material for Lithium‐Ion Batteries

Achieving high initial coulombic efficiency and low voltage dropping in Li-rich Mn-based cathode materials by Metal-Organic frameworks-derived coating

Mild Lithium‐Rich Manganese‐Based Cathodes with the Optimal Activation of Li2MnO3 for Stable and High Capacity Lithium‐Ion Batteries

Na-substitution induced oxygen vacancy achieving high transition metal capacity in commercial Li-rich cathode

Controllable oxygen vacancies (in surface and bulk) to suppress the voltage decay of Li-rich layered cathode

Unlocking The Potential of Li‐rich Mn‐based Oxides for High‐rate Rechargeable Lithium‐ion Batteries