Correction to: Shear properties and pore structure characteristics of soil–rock mixture under freeze–thaw cycles

Liyun Tang,Gang Li,Zhen Li,Long Jin,Gengshe Yang

DOI: https://doi.org/10.1007/s10064-021-02169-7

IF: 4.2

2021-03-04

Bulletin of Engineering Geology and the Environment

Abstract:A Correction to this paper has been published: https://doi.org/10.1007/s10064-021-02169-7

engineering, environmental,geosciences, multidisciplinary, geological

What problem does this paper attempt to address?

Correction To: Impact of Multiple Drying–wetting Cycles on Shear Behaviour of an Unsaturated Compacted Clay

Rui Chen,Tao Xu,Weidong Lei,Yanru Zhao,Jie Qiao

DOI: https://doi.org/10.1007/s12665-018-7868-6

IF: 2.8

2018-01-01

Environmental Earth Sciences

Abstract:The original article can be found online.
Effect of Different Moisture Content on Mechanical Parameters of Red Clay Under Freeze-Thaw Cycle

Bin Lin,Zhuhua Tian,Liang Jiang,Yongjia Zhao

DOI: https://doi.org/10.21203/rs.3.rs-988887/v1

2021-01-01

Abstract:Abstract One of the causes of damage in cold area projects is the freeze-thaw cycling action, which causes large changes in soil strength, resulting in soil deformation and destroying its soil stability. In order to investigate the effect of water content on the mechanical parameters of red clay soil under the action of freeze-thaw cycles, the solidification undrained triaxial test and consolidation test were carried out with red clay soil in Changzhi area, Shanxi Province, as the research object. The test results show that the stress-strain curve is hardening curve, with the increase of water content, the maximum shear stress, cohesion, internal friction angle, elastic modulus, compression modulus and shear modulus are decreasing, and Poisson ratio is gradually increasing. The mechanical parameters of 0 freeze-thaw cycles are greater than 12 freeze-thaw cycles. With the increase in water content, the difference in shear stress between two freeze-thaw cycles was decreasing under the same circumferential pressure. 0 freeze-thaw cycles, the decreasing trend of cohesion increased from 4.48% to 35.88%, and the elastic modulus decreased up to 69.61%. 12 freeze-thaw cycles, the decreasing trend of cohesion decreased from 65.38% to 5.93%, and the elastic modulus showed a linear decreasing relationship. The decreasing trend of the internal friction angle remained consistent with the gradual increase. The Poisson ratio was 0.21-0.29 and 0.24-0.31 for the two cycles, respectively. The shear modulus at 0 freeze-thaw cycles was 1.86-1.16 times higher than that at 12 freeze-thaw cycles, and the difference decreased gradually with the increase in water content. The increase in water content made the soil more prone to shear deformation.
Author Correction: Microscopic and mechanical properties of undisturbed and remoulded red clay from Guiyang, China

Yanzhao Zhang,Shaoyun Pu,Rita Yi Man Li,Jing Zhang

DOI: https://doi.org/10.1038/s41598-021-81993-z

IF: 4.6

2021-02-03

Scientific Reports

Abstract:An amendment to this paper has been published and can be accessed via a link at the top of the paper.

multidisciplinary sciences
Shear properties and pore structure characteristics of soil–rock mixture under freeze–thaw cycles

Liyun Tang,Gang Li,Zhen Li,Long Jin,Gengshe Yang

DOI: https://doi.org/10.1007/s10064-021-02118-4

IF: 4.2

2021-02-14

Bulletin of Engineering Geology and the Environment

Abstract:Soil–rock mixtures (S-RMs) are widely distributed in the shallow surfaces of cold regions that experience frequent freeze–thaw cycles, considerably threatening the stability of the soil–rock slopes on both sides of the road. We examine the S-RM shear strength and deformation characteristics under different freeze–thaw cycles through experiment and simulation. Nuclear magnetic resonance (NMR) was used to analyze the influence of freeze–thaw cycles on the internal pore structure of S-RM and establish the internal relationship between pore structure and shear characteristics under freeze–thaw cycles. Results show that the shear strength parameters of S-RM first decrease, then increase, and finally decrease as the number of freeze–thaw cycles increases; besides, the vertical expansion range of cracks gradually increases during shearing with the number of cycles. Porosity first increases, then decreases, and increases again with the number of freeze–thaw cycles. NMR results showed that S-RM pores had fractal characteristics. According to the fractal dimension, the soil particles inside the sample formed larger aggregates after the first freeze–thaw cycle. After the second–third freeze–thaw cycles, the agglomerated soil particles gradually disintegrate and tend to homogenize. The soil particles cover the surface of the gravel under the skeleton deformation to form an inclusion structure. The subsequent increase in the number of freeze–thaw cycles causes the soil particles attached to the gravels to gradually peel off.

engineering, environmental,geosciences, multidisciplinary, geological
Volumetric behavior of an unsaturated clayey soil-rock mixture subjected to freeze-thaw cycles: A new insight

Yonggan Zhang,Yang Lu,Sihong Liu,Binxin Fang,Zhuo Li,Kang Liu

DOI: https://doi.org/10.1016/j.coldregions.2022.103608

IF: 4.427

2022-09-01

Cold Regions Science and Technology

Abstract:The volumetric behavior of clayey soil-rock mixtures under freeze-thaw action is very important for the design of anti-frost heave in cold-region engineering. However, existing studies mainly focus on the effect of freeze-thaw cycles on the global volume change of fine-grained soils, and few attempts have focused on mixed soils with coarse particles such as clayey soil-rock mixtures. In this study, a series of laboratory freezing-thawing tests were conducted to investigate the effects of the freeze-thaw cycles and rock content on the global volume change, diameter change, and height change behaviors of cylindrical soil-rock mixture samples. The results demonstrate that: 1) the volumetric behavior of the samples under freeze-thaw cycles is closely related to the rock content, which is mainly because different rock contents dominate the different skeleton structures. 2) For samples with 0%, 10%, and 30% rock content, the global volume of compacted samples shows shrinkage upon freezing and expansion after thawing. However, the global volume of the sample with 50% rock content began to shrink after three freeze-thaw cycles. 3) Compared with the samples not subjected to freeze-thaw weathering, the height of samples with 0%, 10%, and 30% rock content shows shrinkage upon freezing and expansion after thawing no matter what the number of freeze-thaw cycles is. However, the diameter and height of the sample are always shrinking, regardless of whether they are frozen or thawed. 4) Upon freezing, the shrinkage of the sample's global volume and diameter tends to decrease linearly with the increase of rock content, but the shrinkage of the sample's height is not sensitive to the change of rock content. Upon thawing, the global volume and height of the sample exhibit a trend from expansion to contraction with increasing rock content, but the shrinkage of the diameter of the sample is nearly the same no matter what the rock content is. Furthermore, a computed tomography (CT)-based mesoscopic structural characteristic and two idealized schematic diagrams well illustrated the evolution mechanism of the volumetric behavior of an unsaturated clayey soil-rock mixture subjected to freeze-thaw cycles.

engineering, environmental, civil,geosciences, multidisciplinary
Mechanism of shear strength deterioration of soil-rock mixture after freeze–thaw cycles

Liyun Tang,Gang Li,Tao Luo,Long Jin,Yongtang Yu,Qiang Sun,Guoyu Li

DOI: https://doi.org/10.1016/j.coldregions.2022.103585

IF: 4.427

2022-08-01

Cold Regions Science and Technology

Abstract:The growth and melting of internal ice crystals reorganizing the pore structure and internal skeleton of soil-rock mixture (S-RM), which leads to the deterioration of the S-RM shear strength after freeze–thaw cycles and its strength characteristics after the cycles are different from the normal temperature one. Due to unclear S-RM strength deterioration mechanism after freeze–thaw cycles, stability of S-RM cutting slopes in cold regions cannot be effectively evaluated. In this paper, particle flow code (PFC) simulation as well as direct shear and nuclear magnetic resonance (NMR) tests were carried to study strength degradation behaviors and pore structure changes of S-RMs containing various amounts of rock after freeze–thaw cycles. The results show that the shear strength and internal friction angle of S-RM are no longer positively correlated with the rock content after the cycles, and the strength parameters will decrease at rock contents of above 45%. Based on the simulation test, shear band thickness variation after the cycles was quantitatively evaluated, and an innovative method to obtain the fluctuation value of shear failure surface was proposed. It is found that the change laws of shear band thickness and failure surface fluctuation value with rock content after the cycles are consistent with that of shear strength, and they all reach the maximum value when the rock content is 45%. Fractal theory was introduced for quantitative evaluation of changes in S-RM pore structure after the cycles, and combined with the strength parameter attenuation, the strength deterioration mechanism of S-RM was revealed: The deterioration of shear strength in samples containing low rock content is mainly due to changes in the contact form between particles caused by internal inclusion structure formation after the cycles. The deterioration of S-RM with rock content of 55% and 65% is mainly due to attenuation of the internal skeleton effect caused by the appearance of overhead structures. The internal pores and skeleton structure of the sample with 45% rock content have little change, so the attenuation changes of the strength parameters and the undulation value of the failure surface are minimal.

engineering, environmental, civil,geosciences, multidisciplinary
Cyclic Freeze–thaw Induced Stiffness Anisotropy of Sandy Silt under All-Round and Unidirectional Freezing Modes

Shuai Zhang,Dashuang Wang,Daniel Peprah-Manu,Yikai Wang,Charles W. W. Ng

DOI: https://doi.org/10.1016/j.catena.2023.107749

IF: 6.367

2024-01-01

CATENA

Abstract:The stiffness anisotropy of soil is a critical factor that influences the deformation characteristics of soil in landform evolution, geological disaster mitigation and engineering applications. However, the effects of freeze-thaw cycles on the stiffness anisotropy of soil have not been clearly understood. In this study, a new thermal boundary-controlled triaxial testing system equipped with bender elements is developed to investigate the effects of cyclic freeze-thaw on the stiffness of a sandy silt under both unidirectional and all-round freezing modes. It is revealed that under all-round freeze-thaw cycles, the shear wave velocity in the horizontal and vertical planes undergoes a continuous increase of 14% and 8%, respectively. In contrast, unidirectional freeze-thaw leads to a non-monotonic evolution of shear wave velocity, eventually resulting in a 3% reduction in the horizontal plane and a 16% reduction in the vertical plane after 10 freeze-thaw cycles. The increase in shear stiffness anisotropy of the sandy silt after freeze-thaw cycles is more significant in the unidirectional freeze-thaw condition (from 1.11 to 1.49) compared with the all-round freeze-thaw condition (from 1.13 to 1.19). This study illustrates the significance of unidirectional freeze-thaw in the evolution of mechanical anisotropy of soils in cold regions.
Erratum to: An Experimental Study of the Effects of Filling Degree on Shear Behavior and Acoustic Emission Characteristics of Kaolinite-Filled Granite Joints

Yangbing Cao,Yaoyao Zhang,Zhi Liu,Min Bao

DOI: https://doi.org/10.1007/s12205-024-7085-7

IF: 2.115

2024-07-26

KSCE Journal of Civil Engineering

Abstract:This erratum is published to notify a correction in Eq. (6).

engineering, civil
Correction to: The effects of soil shrinkage during centrifuge tests on SWCC and soil microstructure measurements

Lincui Li,Xi-An Li,Li Wang,Bo Hong,Jianfeng Shi,Jianqiang Sun

DOI: https://doi.org/10.1007/s10064-020-02024-1

IF: 4.2

2020-11-12

Bulletin of Engineering Geology and the Environment

Abstract:The original version of Fig. 7 included one incorrect image.

engineering, environmental,geosciences, multidisciplinary, geological
Influence of freeze-thaw cycles on the shear performance of silty clay-concrete interface

Boxin Wang,Jiaqi Liu,Qing Wang,Xianzhang Ling,Jingjing Pan,Ruichang Fang,Zilong Bai

DOI: https://doi.org/10.1016/j.coldregions.2024.104120

IF: 4.427

2024-01-07

Cold Regions Science and Technology

Abstract:In regions with seasonal frozen soil, mechanical properties of soil are impacted by freeze-thaw cycles, which influence the shear resistance of soil-concrete interface in geotechnical engineering. For evaluating shear properties at the soil-concrete interface, freeze-thaw cycles and direct shear experiments were conducted in this research. The stress-displacement curves, shear strength and parameters of the interface were analyzed in relation to freeze-thaw cycles, while the influences by moisture contents and normal stresses were considered. Results show that the curves related to shear stresses and displacements at the interface are strain-hardening, and shear properties gradually deteriorate with repetitive freezing and thawing. The shear strength is positively related to normal stresses, and it increases by approximately 250% while normal stress varies from 100 to 400 kPa. However, it is negatively correlated with growing moisture contents and freeze-thaw cycles. The reduction in shear strength is about 21%–25% after freeze-thaw cycles, along with a decrease in cohesion ranging from 14% to 20% and for angle of internal friction it reaches at 14%–24%. Moreover, an improved hyperbolic model based on the logistic function and hyperbolic model was established to evaluate shear properties at the interface under freeze-thaw cycles, providing a theory base for engineering construction in seasonally frozen soil regions.

engineering, environmental, civil,geosciences, multidisciplinary
Effects of cyclic freezing and thawing on the shear behaviors of an expansive soil under a wide range of stress levels

Wei-lie Zou,Zhong Han,Gui-tao Zhao,Ke-wei Fan,Sai K. Vanapalli,Xie-qun Wang

DOI: https://doi.org/10.1007/s12665-022-10190-6

IF: 2.8

2022-01-25

Environmental Earth Sciences

Abstract:The focus of this paper was directed towards investigating the influence of multiple freeze–thaw (FT) cycles on the mechanical behaviors of an expansive soil under a wide range of confining stresses (σc) from 0 to 300 kPa. Consolidated undrained (CU) shear tests with pore pressure measurement (σc = 10–300 kPa) and unconfined compression (UC) tests (σc = 0 kPa) were conducted on FT impact specimens to derive the shearing stress–strain relationships and the associated mechanical properties including (i) failure strength (qu), elastic modulus (Eu), effective and apparent cohesion (c′ and c), and effective and apparent friction angle (ϕ′ and ϕ) obtained from CU tests and (ii) qu and reloading modulus (E1%) and stress (Su1%) at 1% strain obtained from UC tests. Besides, the influence of FT cycles on the soil structure was investigated using mercury intrusion porosimetry (MIP) and scanning electron microscope (SEM) tests. Testing results show that FT cycles mainly influence the soil’s macropores with diameters between 5 and 250 μ. Cracks develop during FT cycles and result in slight swelling which contributes to an increase in the global volume of the soil specimens. There is a significant reduction in the investigated mechanical properties after FT cycles. They typically achieve equilibrium after about six cycles. The shearing stress–strain curves transit from strain-softening to strain-hardening as the confining stress increases. A simple empirical model is developed to well describe the strain-softening behavior of the stress–strain curves under low confining stresses.

environmental sciences,water resources,geosciences, multidisciplinary
Study of the Mechanical and Microscopic Properties of Modified Silty Clay under Freeze-Thaw Cycles

Zhou Wenjun,Wang Qingzhi,Fang Jianhong,Wang Kejin,Zhao Xiangqing

DOI: https://doi.org/10.1155/2022/9613176

IF: 2.006

2022-03-14

Geofluids

Abstract:Silty clay can be found in the alpine region of the Qinghai province, China, where it is subject to annual freeze-thaw cycles. To investigate the static mechanical properties of silty clay modified by basalt fiber and basalt powder under the action of freeze-thaw cycles, triaxial compression tests and scanning electron microscope tests were conducted on the soil. The test results revealed that varying the number of freeze-thaw cycles resulted to different effects on the soil mechanical strength, which tended to increase after 2 cycles, but then tended to decline when subjected to 5–10 cycles. After 20 freeze-thaw cycles, soil strength reached a dynamic equilibrium state. The shear strength of basalt fiber soil and basalt powder soil increased by 7.55% and 5.12%, respectively, compared with that of normal soil under 30 freeze-thaw cycles. Subsequently increasing of the number of freeze-thaw cycles differentially affected the cohesion and internal friction angle of normal soil and admixture soils, and these soils gradually tended to stabilize at a mechanical strength higher than the initial value. Basalt fibers reinforced the soil to a higher degree than basalt powder at a dosage of 0.4% based on dry soil mass. The stress-strain curves of the three soil types can be simulated using the hyperbolic model. The results of the study can provide some theoretical reference for practical engineering in seasonal frozen soil areas.

geochemistry & geophysics,geology
Effect of Freeze-Thaw Cycles on the Shear Strength of Root-Soil Composite

Qi Liu,Jiankun Huang,Zhiwei Zhang,Gongming Liu,Qunou Jiang,Lanhua Liu,Inam Khan

DOI: https://doi.org/10.3390/ma17020285

2024-01-05

Abstract:A large alpine meadow in a seasonal permafrost zone exists in the west of Sichuan, which belongs to a part of the Qinghai-Tibet Plateau, China. Due to the extreme climates and repeated freeze-thaw cycling, resulting in a diminishment in soil shear strength, disasters occur frequently. Plant roots increase the complexity of the soil freeze-thaw strength problem. This study applied the freeze-thaw cycle and direct shear tests to investigate the change in the shear strength of root-soil composite under freeze-thaw cycles. This study examined how freeze-thaw cycles and initial moisture content affect the shear strength of two sorts of soil: uncovered soil and root-soil composite. By analyzing the test information, the analysts created numerical conditions to foresee the shear quality of both sorts of soil under shifting freeze-thaw times and starting moisture levels. The results showed that: (1) Compared to the bare soil, the root-soil composite was less affected by freeze-thaw cycles in the early stage, and the shear strength of both sorts of soil was stabilized after 3-5 freeze-thaw cycles. (2) The cohesion of bare soil decreased more than that of root-soil composite with increasing moisture content. However, freeze-thaw cycles primarily influence soil cohesion more than the internal friction angle. The cohesion modification leads to changes in shear quality for both uncovered soil and root-soil composite. (3) The fitting equations obtained via experiments were used to simulate direct shear tests. The numerical results are compared with the experimental data. The difference in the soil cohesion and root-soil composite cohesion between the experiment data and the simulated result is 8.2% and 17.2%, respectively, which indicates the feasibility of the fitting equations applied to the numerical simulation of the soil and root-soil composite under the freeze-thaw process. The findings give potential applications on engineering and disaster prevention in alpine regions.
Post-peak mechanical property and a new strain softening model for rocks subjected to freeze–thaw cycles

Feng Gao,Jinxi Xie,Xin Xiong,Keping Zhou

DOI: https://doi.org/10.1007/s12665-023-11223-4

IF: 2.8

2023-10-25

Environmental Earth Sciences

Abstract:In this paper, the mechanical properties and strain softening model of rock in cold regions after the peak were investigated. Freeze–thaw cycle tests and triaxial compression tests were performed on green sandstone to obtain stress–strain curves for rocks under different freeze–thaw cycles. The deformation, strength, and post-peak characteristics of rocks under freeze–thaw cycles and triaxial compression were analyzed, including brittleness and drop degree. On this basis, the experimental data were used to draw the Mohr stress circle and its corresponding envelope under different freeze–thaw cycles and confining pressure conditions. It also determines the generalized cohesion and the generalized internal friction angle under different freeze–thaw cycles and confining pressure conditions. Least square surface fitting was used to obtain the softening law of post-peak strength parameters of frozen–thawed rock. Finally, a constitutive model was established that accurately reflects the post-peak strain softening behavior of rock under freeze–thaw cycles. The model uses the maximum principal strain as the softening parameter and subjects the strength parameters (generalized cohesion , generalized internal friction angle ) to piecewise linear evolution according to the Mohr–Coulomb criterion. The paper concludes by comparing and analyzing the influence of each strength parameter on the post-peak strain softening behavior of rock.

environmental sciences,water resources,geosciences, multidisciplinary
Erratum to: Description of full-range strain hardening behavior of steels

Tao Li,Jinyang Zheng,Zhiwei Chen

DOI: https://doi.org/10.1186/s40064-016-2998-3

2016-01-01

SpringerPlus

Abstract:[This corrects the article DOI: 10.1186/s40064-016-2998-3.].
Experimental investigation on the temperature-dependent shear strength of frozen coarse-grained soil-rock interfaces by considering three-dimensional roughness

Yonglong Yang,Shibing Huang,Shuyang Yu,Haowei Cai,Jiawei Zhai

DOI: https://doi.org/10.1016/j.trgeo.2024.101434

IF: 4.938

2024-11-12

Transportation Geotechnics

Abstract:Climate warming has led to landslides, especially the slopes containing soil-rock interfaces. A series of shear tests were conducted on the coarse-grained soil (CGS) rock interface at low temperatures. The interface shear strength comprises the pre-peak bonding strength produced by ice and post-peak residual strength created by friction between the CGS and rock surface. As the temperature rose from −15 to −1 °C, the bonded ice strength at different rough interfaces rapidly decreased by a maximum of 82.99 %, because more than 21.29 % of the pore ice had thawed within the CGS. However, the average interface residual strength had decreased by only 18.56 %, which is consistent with the variation of the internal friction angle of the frozen CGS. The interfacial shear strength was much lower than the shear strength of the frozen CGS below −1 °C and that the shear slide typically occurred at the interface. In addition, as the freezing temperature increased, the impact of the three-dimensional roughness to the interfacial shear strength decreased, because the warm frozen CGS could easily shear rupture and adhere to the interface, reducing the influence of the roughness. Finally, it was demonstrated that the Mohr-Coulomb failure criterion could be employed to predict the interface peak shear strength for different normal stresses. This study aims to determine the mechanism responsible for shear strength reduction at a frozen CGS-rock interface during warming and to provide some references for preventing landslides caused by rising temperatures.

engineering, civil, geological
Correction: Exploring the Mpemba effect: a universal ice pressing enables porous ceramics

Xiaodan Yang,Yao Shan,Ying Hong,Zhuomin Zhang,Shiyuan Liu,Xiaodong Yan,Xuetian Gong,Guangzu Zhang,Zhengbao Yang

DOI: https://doi.org/10.1039/d3mh01869e

IF: 13.3

2024-03-20

Materials Horizons

Abstract:Correction for 'Exploring the Mpemba effect: a universal ice pressing enables porous ceramics' by Xiaodan Yang et al. , Mater. Horiz. , 2024, DOI: https://doi.org/10.1039/d3mh01869e.

materials science, multidisciplinary,chemistry
Correction to "Proppant Settlement and Long-Term Conductivity Calculation in Complex Fractures"

Xiaopeng Wang,Xiaocheng Zhang,Ming Zhang,Qilong Zhang,Pinghua Dong,Haibo Ding,Xiaoqiang Liu

DOI: https://doi.org/10.1021/acsomega.4c06552

IF: 4.1

2024-08-21

ACS Omega

Abstract:[This corrects the article DOI: 10.1021/acsomega.3c08594.].
Orthogonal experimental study of soil–rock mixtures under the freeze–thaw cycle environment

Zhong Zhou,Fan Li,Hao Yang,Wenyuan Gao,Linwu Miao

DOI: https://doi.org/10.1080/10298436.2019.1686634

2019-11-07

International Journal of Pavement Engineering

Abstract:Soil–rock mixtures is a special engineering geological material and often used as a roadbed filler. Based on the orthogonal experimental method, a series of large-scale triaxial tests of soil–rock mixtures under the freeze–thaw cycle environment was designed with five factors including rock content, compaction degree, moisture content, number of freeze–thaw cycles and freezing temperature at four experimental levels, respectively. Then, the effect of each orthogonal experimental factor and the effect of the confining pressure on the statics mechanical characteristics of the soil–rock mixtures were statistically investigated by range and variance analysis. Research results showed that the static stress of the soil–rock mixtures is linearly positively correlated with the confining pressure; for different confining pressures, the most crucial factors to affect the static stress are different; for the shear strength, the most crucial factors to affect the cohesive force and friction angle are correspondingly number of freeze–thaw cycles and rock content. The study of the crucial influence factors at different confining pressures after freeze–thaw cycles can provide guidance for design and protection of soil–rock mixtures under different environment.

construction & building technology,engineering, civil,materials science, characterization & testing
Author Correction: Nano-scale structure and mechanical properties of ASR products under saturated and dry conditions

Huite Wu,Jianwen Pan,Jinting Wang

DOI: https://doi.org/10.1038/s41598-020-69840-z

IF: 4.6

2020-07-28

Scientific Reports

Abstract:An amendment to this paper has been published and can be accessed via a link at the top of the paper.

multidisciplinary sciences

Correction to: Shear properties and pore structure characteristics of soil–rock mixture under freeze–thaw cycles

Correction To: Impact of Multiple Drying–wetting Cycles on Shear Behaviour of an Unsaturated Compacted Clay

Effect of Different Moisture Content on Mechanical Parameters of Red Clay Under Freeze-Thaw Cycle

Author Correction: Microscopic and mechanical properties of undisturbed and remoulded red clay from Guiyang, China

Shear properties and pore structure characteristics of soil–rock mixture under freeze–thaw cycles

Volumetric behavior of an unsaturated clayey soil-rock mixture subjected to freeze-thaw cycles: A new insight

Mechanism of shear strength deterioration of soil-rock mixture after freeze–thaw cycles

Cyclic Freeze–thaw Induced Stiffness Anisotropy of Sandy Silt under All-Round and Unidirectional Freezing Modes

Erratum to: An Experimental Study of the Effects of Filling Degree on Shear Behavior and Acoustic Emission Characteristics of Kaolinite-Filled Granite Joints

Correction to: The effects of soil shrinkage during centrifuge tests on SWCC and soil microstructure measurements

Influence of freeze-thaw cycles on the shear performance of silty clay-concrete interface

Effects of cyclic freezing and thawing on the shear behaviors of an expansive soil under a wide range of stress levels

Study of the Mechanical and Microscopic Properties of Modified Silty Clay under Freeze-Thaw Cycles

Effect of Freeze-Thaw Cycles on the Shear Strength of Root-Soil Composite

Post-peak mechanical property and a new strain softening model for rocks subjected to freeze–thaw cycles

Erratum to: Description of full-range strain hardening behavior of steels

Experimental investigation on the temperature-dependent shear strength of frozen coarse-grained soil-rock interfaces by considering three-dimensional roughness

Correction: Exploring the Mpemba effect: a universal ice pressing enables porous ceramics

Correction to "Proppant Settlement and Long-Term Conductivity Calculation in Complex Fractures"

Orthogonal experimental study of soil–rock mixtures under the freeze–thaw cycle environment

Author Correction: Nano-scale structure and mechanical properties of ASR products under saturated and dry conditions