Abstract:Thermal interface materials (TIMs) are indispensable materials in thermal management, and Al2O3-based TIMs are most widely used in thermal managements. Surface modification is an effective method to improve Al2O3 dispersion in matrix, thereby increasing the maximum filler loading. However, traditional surfactants hardly promote the interfacial heat-transfer on the premise of the same filler loading. In this work, we proposed an electrostatic self-assembly strategy to functionalize the surface of Al2O3 particles with MXene sheets to enhance the interfacial heat-transfer between fillers and silicone rubber (SR). To validate the effectiveness of MXene, we compared the Al2O3-MXene-SR TIM with Al2O3-graphene-SR TIM and Al2O3-SR TIM under the same Al2O3 loading in the aspects of mechanical properties and thermal properties. Though MXene could increase the viscosity and hardness, the negative influence of MXene is much weaker than that of graphene. Nevertheless, the positive impact of MXene is more significant. First, it can reinforce the mechanical strength. The experiment showed the breaking tensile strength of the Al2O3-MXene-SR TIM is 0.117 MPa, higher than that of the Al2O3-graphene-SR TIM (0.082 MPa) and the Al2O3-SR TIM (0.07 MPa). Second, the thermal conductivity of TIMs improves a lot after MXene coating. The thermal conductivity of Al2O3-MXene-SR TIM is 3.4 W·m−1·K−1, with the matrix/filler mass ratio of 100:1600, which is 30% higher than that of the Al2O3-SR TIM (2.6 W·m−1·K−1) and 21% higher than that of Al2O3-Gr-SR TIM (2.8 W·m−1·K−1). Whereas the Al2O3 loading keeps the same and the MXene fraction is only about 1.16 vol‰, the increment of the thermal conductivity is mostly due to the improvement of interfacial heat-transfer via MXene. The temperature cycling test and aging test implied that the Al2O3-MXene-SR TIM is thermally stable and reliable. The underlying mechanism of the interfacial heat-transfer enhancement was revealed by the analysis of phonon density of states (PDOS) via a molecular dynamics simulation. The PDOS of MXene is more compatible with Al2O3 and SR than graphene, so MXene sheets play the role as a bridge between Al2O3 and SR to improve the interfacial phonon transport. This work provides an effective method to reduce interfacial thermal resistance in TIMs, which could facilitate the development of thermal management materials.

Effect of various nanoparticle fillers on the thermal contact resistance (TCR) between crystals and aluminium alloys materials

Low Interfacial Thermal Resistance Between Crossed Ultra-Thin Carbon Nanothreads

Experimental Study of Thermal Contact Resistance Between Aluminium Alloy and ADP Crystal under Vacuum Environment

Effect of hybrid nanofillers on thermal conductivity of composite phase change materials

Enhanced Thermal and Dielectric Performance of Epoxy Resin/aluminum Nitride Nanocomposites at High Temperatures

Effect of spherical alumina crystalline phase content and particle size distribution polydispersity on the properties of silicone rubber composites

Enhancement on Heat Transfer and Reliability of Low Melting Temperature Alloy Based Thermal Interface Materials

Effect of Surface Functionalization of Si3N4 Fillers on Thermal and Mechanical Properties of TIMs

Experimental investigation on thermal contact resistance of alumina fibrous insulation material with Ti-6Al-4V alloy at high temperature and its effective thermal conductivity

Thermal Contact Resistance of Epoxy Composites Incorporated with Nano-Copper Particles and the Multi-Walled Carbon Nanotubes

Highly Enhanced Thermal Conductivity of Epoxy Composites by Constructing Dense Thermal Conductive Network with Combination of Alumina and Carbon Nanotubes

Enhanced interfacial heat-transfer of Al2O3-MXene-silicone composite via an electrostatic self-assembly strategy

Effects of TiC0.5N0.5 Nanoparticles on the Microstructure, Mechanical and Thermal Properties of TiC0.5N0.5/Al-Cu Nanocomposites

Effect of the alumina micro-particle sizes on the thermal conductivity and dynamic mechanical property of epoxy resin

Effect of filler orientation induced by force on thermal conductivity of AlN/BN/CNTs/SR composites

Effect of Al2o3 Nano-Fillers on the High-Temperature Heat Insulation Performances of Metallic Hollow Microlattice Material

Nanoparticles Enabled Mechanism for Hot Cracking Elimination in Aluminum Alloys

Optimization of Effective Thermal Conductivity of Thermal Interface Materials Based on the Genetic Algorithm-Driven Random Thermal Network Model

Comprehensive excellent performance for silicone-based thermal interface materials through the synergistic effect between graphene and spherical alumina

Thermal Data of Perfluorinated Carboxylic Acid Functionalized Aluminum Nanoparticles

Enhancement of thermal conductivity and insulation of silicone thermal interface material through surface modification and synergistic effects of nanofillers for thermal management of electronic devices