Abstract:Recent advances in additive manufacturing (AM) have enabled the fabrication of functionally graded porous biomaterials (FGPBs) for application as orthopedic implants and bone substitutes. Here, we present a step-wise topological design of FGPB based on diamond unit cells to mimic the structure of the femoral diaphysis. The FGPB was manufactured from Ti-6Al-4V powder using the selective laser melting (SLM) technique. The morphological parameters, permeability and mechanical properties of FGPB samples were measured and compared with those of the biomaterials with uniform porous structures based on the same type of the unit cell. The FGPB exhibited a low density (1.9 g/cm3), a moderate Young's modulus (10.44 GPa), a high yield stress (170.6 MPa), a high maximum stress (201 MPa) and favorable ductility, being superior to the biomaterials with uniform porous structures in comprehensive mechanical properties. In addition, digital image correlation (DIC) and finite element (FE) simulation were used to unravel the mechanisms governing the deformation and yielding behavior of these biomaterials particularly at the strut junctions. Both DIC and FE simulations confirmed that the deformation and yielding of the FGPB occurred largely in the load-bearing layers but not at the interfaces between layers. Defect-coupled FE models based on solid elements provided further insights into the mechanical responses of the FGPB to compressive loads at both macro- and micro-scales. With the defect-coupled representative volume element model for the FGPB, the Young's modulus and yield stress of the FGPBs were predicted with less than 2% deviations from the experimental data. The study clearly demonstrated the capabilities of combined experimental and computational methods to resolve the uncertainties of the mechanical behavior of FGPBs, which would open up the possibilities of applying various porosity variation strategies for the design of biomimetic AM porous biomaterials. STATEMENT OF SIGNIFICANCE: Functionally graded bone scaffolds significantly promote the recovery of segmental bone defect. In the present study, we present a step-wise topological design of functionally graded porous biomaterial (FGPB) to mimic the structure of the femoral diaphysis. The Ti-6Al-4V FGPB exhibited a superior combination of low density, moderate Young's modulus, high yield stress and maximum stress as well as favorable ductility. The biomechanical performance of FGPB was studied in both macro and micro perspectives. The defect-coupled model revealed the significant yielding in the load-bearing parts and the Young's modulus and yield stress of the FGPBs were predicted with less than 2% deviations from the experimental data. The superiority of combined experimental and computational methods has been confirmed.

Influence of conical graded porous architecture on the mechanical, failure behavior and fluid-flow properties for bone scaffold application

Mechanical and degradation properties of triply periodic minimal surface (TPMS) hydroxyapatite & akermanite scaffolds with functional gradient structure

Compressive properties and energy absorption of selective laser melting formed Ti-6Al-4V porous radial gradient scaffold

Gyroid-based functionally graded porous titanium scaffolds for dental application: Design, simulation and characterizations

Parametric Design of Porous Structure and Optimal Porosity Gradient Distribution Based on Root-Shaped Implants

Multi-objective Shape Optimization of Bone Scaffolds: Enhancement of Mechanical Properties and Permeability

Full compression response of FG-based scaffolds with varying porosity via an effective numerical scheme

Computational study promoting engineering biomaterial pre-design to well adapt pores distribution on bone/scaffold assembly section

Analysis of Mechanical Properties and Permeability of Trabecular-Like Porous Scaffold by Additive Manufacturing

Investigation of Mechanical and Biological Properties of FDM 3D-Printed PLA Scaffolds With Radial Gradient Porosity for Tissue Engineering

Biomechanical Influence of Structural Variation Strategies on Functionally Graded Scaffolds Constructed with Triply Periodic Minimal Surface

Finite element analysis of gradient lattice structure patterns for bone implant design

Design of a Haversian System-Like Gradient Porous Scaffold Based on Triply Periodic Minimal Surfaces for Promoting Bone Regeneration

Investigating wall shear stress and the static pressure in bone scaffolds: a study of porosity and fluid flow dynamics

Design of graded porous bone-like structures via a multi-material topology optimization approach

Parametric design and performance study of continuous gradient triply periodic minimal surface bone scaffold

Topological design, permeability and mechanical behavior of additively manufactured functionally graded porous metallic biomaterials

Design of biomedical gradient porous scaffold via a minimal surface dual-unit continuous transition connection strategy

Design and analysis of the mechanical properties of controllable porous scaffolds for bone tissue engineering

Modeling, Assessment, and Design of Porous Cells Based on Schwartz Primitive Surface for Bone Scaffolds

Effect of porosity variation strategy on the performance of functionally graded Ti-6Al-4V scaffolds for bone tissue engineering