Abstract:In rock materials, the intergranular structure is more affected by various external conditions than the transgranular structure, and then dominates the macroscopic mechanical properties of rocks. In this paper, an innovative three‐dimensional grain‐based model based on Particle Flow Code (PFC3D‐GBM) for reproducing granite crystalline structures was developed. Based on this model, the Brazilian splitting test was conducted to investigate the effects of intergranular contact (IC) bonding strength on the mechanical properties and micro‐cracking behavior of the granite. Additionally, in this paper, the force chains and the orientation distribution of the force chains are shown in the form of three‐dimensional rose diagrams. The results are compared to the numerical results obtained by an initial particle‐based model to demonstrate the superiority of the proposed PFC3D‐GBM. The results indicate that the stress–strain curve of the sample in the Brazilian splitting test can be classified into four distinct stages: initial compaction, linear elasticity, damage, and splitting failure. ICs fracture at a higher rate than transgranular contacts (TCs) under static loading, as evidenced by experimental results of laboratory tests; during the entire loading process, all force chains uniformly distribute in all directions of a sample. As the external load increases, the number of total force chains decreases and the number of cracks increases. The main orientation of the high‐strength force chains is consistent with the external loading direction and is vertical with respect to the main orientation of the cracks. Furthermore, the number of high‐strength force chains increases with the level of external load. The sample's failure mechanism in the Brazilian splitting test is always a tensile failure, and this characteristic is unaffected by the modeling method or the IC bonding strength. Both the tensile strength and peak strain increase as the IC bonding strength increases. In this process, the number of total cracks in PFC3D‐GBM decreases, the proportion of transgranular cracks (Tcs) increases, and the proportion of intergranular cracks (Ics) decreases. The micro‐cracking behavior described above based on the PFC3D‐GBM can be explained more rationally. As the bonding strength of the IC increases, the particles involved in sample deformation are subjected to a greater stress concentration prior to the sample experiencing macro‐fracture, leading to an increase in the number of high‐strength force chains, which is the fundamental reason for the increase of the sample's tensile strength.

Numerical investigation on the effect of intergranular contact bonding strength on the mechanical properties of granite using PFC3D‐GBM

Numerical investigation of the effects of the micro-parameters of the transgranular contact on the mechanical response of granite

Numerical investigation of the effect of grain size-to-particle size ratio on the dynamic fracture toughness of granite by using PFC3D-GBM

Quantitative analysis of grain size effect on tensile mechanical behavior of granite based on multi-level force chain networks

Modeling Crack Propagation in Heterogeneous Granite Using Grain-Based Phase Field Method

Analysis of Multi-Level Force Chain Network in Granite Tensile Fracture Based on 3D-GBM

Influence of Mesoscopic Defects on the Mechanical Behaviour of Granites Based on a Three-Dimensional Multilevel Force Chain Network

Experimental and GBM3D study on the failure mechanical behavior of granite with different grain sizes under conventional triaxial compression

Mode I fracture behavior of heterogeneous granite: Insights from grain-based FDEM modelling

A multilevel parallel bonded-grain based model (Multi Pb-GBM) accounting for microstructure failures of typical crystalline rocks

A Modeling Study of the Micro-Cracking Behavior of Brittle Crystalline Rocks under Uniaxial Loading Considering Different Scenarios of Grain-Based Models

Study on the characteristics of granite rock impact crack based on grain-based model

Role of Loading Rate on Cracking Behavior in Granite Disks With Laboratory Experiments and Grain‐Based Modeling

Heterogeneities of grain boundary contact for simulation of laboratory-scale mechanical behavior of granitic rocks

The Influence of Mechanical Heterogeneity of Grain Boundary on Mechanical and Microcracking Behavior of Granite Under Mode I Loading Using a Grain-Based Model

Investigation of the Quasi-Brittle Failure of Alashan Granite Viewed from Laboratory Experiments and Grain-Based Discrete Element Modeling

Investigation of the dynamic behavior and fracturing mechanism of granite

Investigation of Damage Evolution in Heterogeneous Rock Based on the Grain-Based Finite-Discrete Element Model

Modeling Micro-cracking Behavior of Bukit Timah Granite Using Grain-Based Model

Microcrack Growth Behavior And Cwfs Criterion Parameters Optimization Of Granite With Pfc

Stress‐Confinement Effect on the Dynamic Mechanical Properties of Heterogeneous Granite Under Impact Loading: Experimental and Numerical Simulation