Abstract:The trade-off between the safety and effectiveness of NiTi wire in practical applications has consistently hindered its advancement. This underscores the significance of adjusting its microstructure via appropriate heat-treatment techniques. This study systematically investigates the evolution of the constitution phases of the matrix and the grain size as the aging time increases from three minutes to three hours at 550 °C for Ni50.9Ti49.1 wire, and highlights the significant role of the R phase in static/cyclic tensile failure behavior. When aged for thirty minutes, the matrix consists mainly of the B2 phase, similar to the as-received wire, while it tends to transform into the R phase during loading (intermediate-R phase). In contrast, aging for three hours leads to the formation of the R phase as the matrix phase (matrix-R phase). The two types of R phase are discussed and compared in detail with regard to their contribution to the static/cyclic tensile failure behaviour. The longest fatigue life was obtained in wires with the R phase as the matrix phase, which was due to the combined effect: (i) the rapid attainment of a stable state so as to minimise the extent of phase transformation; (ii) coordination deformation of twin and dislocation to alleviate stress concentration; (iii) and the strong bonding between Ti2Ni and the matrix that reduces the occurrence of the "stretching into the hole-coalescence-microcrack process". The enhanced flexibility observed in the wire with matrix-R phase is due to its reduced elastic modulus and lower transformation plateau. The increase in plasticity is linked to changes in the wire's fracture behavior resulting from grain growth. Such microstructural changes allow the alloy wire to exhibit a more uniform plastic deformation under stress, which in turn postpones the onset of significant fracturing.

Effect of carbon addition on the microstructure and mechanical behavior of near equiatomic NiTi alloy wire

Study on the Role of Carbon in Modifying Second Phase and Improving Tensile Properties of NiTi Shape Memory Alloys Fabricated by Electron Beam Directed Energy Deposition

Influence of carbon addition on mechanical properties and microstructures of Ni-free Co-Cr-W alloys subjected to thermomechanical processing

Effect of carbon addition on microstructure and mechanical properties of as-cast nickel-based heavy density matrix alloy reinforced by high tungsten content

Effect of carbon addition on microstructure and mechanical properties of a typical hard-to-deform Ni-base superalloy

Effects of carbon concentration on microstructure and mechanical properties of as-cast nickel-free Co-28Cr-9W-based dental alloys

Effect of carbon nanotube content on the microstructure and mechanical properties of CNTs/TiAl alloys

Unraveling role of Co addition in microstructure and mechanical properties of biomedical Ti-Nb based shape memory alloy

Investigation of the Ageing-Induced R-phase and Its Impact on Static/cyclic Tensile Failure in Ni50.9Ti49.1 Wire

Improvement of mechanical and biological properties of TiNi alloys by addition of Cu and Co to orthodontic archwires

Microstructure and compression behavior of in-situ synthesized Ti2AlC reinforced Ti-48Al-2Cr alloy with carbon nanotubes addition

Carbon addition and temperature dependent tensile deformation resistance and capacity of a low-cost 3rd-generation Ni-based single crystal superalloy

Microstructure and Mechanical Properties of NiTi Alloy Prepared by Double-Wire + Arc Additive Manufacturing Plus In Situ Heat Treatment

Effect of Ni addition on the microstructure, conductivities and mechanical properties of as-cast Al-Fe alloys

Microstructure transformation and mechanical behavior in NiTi alloys fabricated by dissimilar double wires arc additive manufacturing

Effect of carbon alloying on microstructure and mechanical behaviors of Fe35Ni35Cr20Mn10 multi-component alloy

Interstitial Strengthening of a Cast and Wrought Ni-Based Heavy Density Matrix Alloy by Carbon Addition

Microstructures and mechanical properties of NiTi shape memory alloys fabricated by wire arc additive manufacturing

Effect of Ni Content on Microstructure, Mechanical Properties, and Abrasion Behavior of Fe-B-C Alloy

Effect of Cu content on microstructure and properties of Ti-6Al-4V alloy fabricated by double-wire arc additive manufacturing

Effect of Heat Treatment on Fatigue Behaviour of Biomedical Ni–Ti Alloy Wires under Ultrasonic Conditions