Abstract:Ag and its alloys, when prepared by a selective laser melting (SLM) process, have a low density and poor overall performance due to their high reflectivity when the most commonly used laser (λ = 1060 nm) is used, and they have exorbitant thermal conductivity. These characteristics lead to the insufficient melting of the powders and severely limit the applications of additive manufactured silver alloys. To improve the absorption of the laser, as well as for better mechanical properties and higher resistance to sulfidation, Ag–Cu alloys with different La2O3 contents were prepared in this work using the SLM process, via the mechanical mixing of La2O3 nanoparticles with Ag–Cu alloy powders. A series of analyses and tests were conducted to study the effects of La2O3 in Ag–Cu alloys on their density, microstructure, mechanical properties, and corrosion resistance. The results revealed that the addition of La2O3 particles to Ag–Cu alloy powders improved the laser absorptivity and reduced defects during the SLM process, leading to a significant rise from 7.76 g/cm3 to 9.16 g/cm3 in the density of the Ag–Cu alloys. The phase composition of the Ag–Cu alloys prepared by SLM was Silver-3C. La2O3 addition had no influence on the phase composition, but refined the grains of the Ag–Cu alloys by inhibiting the growth of columnar grains during the SLM process. No remarkable preferred orientation existed in all the samples prepared with or without La2O3. An upwards trend was achieved in the hardness of the Ag–Cu alloy by increasing the contents of La2O3 from 0 to 1.2%, and the average hardness was enhanced significantly, from 0.97 GPa to 2.88 GPa when the alloy contained 1.2% La2O3 due to the reduced pore defects and the refined grains resulting from the effects of the La2O3. EIS and PD tests of the samples in 1% Na2S solution proved that La2O3 addition improved the corrosion resistance of the Ag–Cu alloys practically and efficaciously. The samples containing La2O3 exhibited higher impedance values and lower corrosion current densities.

Microstructure and arc erosion behaviors of Ag-CuO contact material prepared by selective laser melting

Investigation of vacuum arc ignition characteristics and erosion morphology microstructure characteristics of CuCr55 electrode contact materials

Anti-Arc Erosion Properties of Ag-La2Sn2O7/SnO2 Contacts

Research on Arc Erosion Products on Silver-metal Oxide Contacts Materials

Microstructure and electrical contact behavior of Al2O3–Cu/30W3SiC(0.5Y2O3) composites

Microstructure, Mechanical Properties, and Corrosion Resistance of Ag–Cu Alloys with La2O3 Fabricated by Selective Laser Melting

Microstructure, mechanical properties and arc erosion behavior of CuW composites prepared by high energy ball milling and spark plasma sintering

Study on the Mechanical Alloying Process for Preparing Ag/LSCO Electrical Contact Material

Simultaneous strength and ductility enhancements of high thermal conductive Ag7.5Cu alloy by selective laser melting

Quasi-Continuous Network Structure Greatly Improved the Anti-Arc-Erosion Capability of Ag/Y2O3 Electrical Contacts

Thermal and arc erosion behavior of CuCr contact material based on large plastic deformation treatment

Arc Erosion and Morphological Characters of Ag/LSCO(12) Contacts by Different Methods

Microstructure, grain and nanowire growth during selective laser melting of Ag–Cu/diamond composites

Selective Laser Melting of Al-7Si-0.5 Mg-0.5Cu: Effect of Heat Treatment on Microstructure Evolution, Mechanical Properties and Wear Resistance

Selective laser melting 316L/CuSn10 multi-materials: Processing optimization, interfacial characterization and mechanical property

CuCr/Cu Contact Material Fabricated Via High-Speed Laser Cladding

Pure copper components fabricated by cold spray (CS) and selective laser melting (SLM) technology

Effect of preparing method of ZnO powders on electrical arc erosion behavior of Ag/ZnO electrical contact material

State of the art and prospects in sliver- and copper-matrix composite electrical contact materials

Electrical Performance of Cu Doped AgSnO<sub>2</sub>In<sub>2</sub>O<sub>3</sub> Electrical Contacts Fabricated by Internal Oxidation

Designing sandwich-structured Ag–SnO 2 contact materials: Overcoming the trade-off between erosion resistance and mechanical properties