Abstract:A supervisory Model Predictive Control (MPC) approach is developed for an air path system for multi-mode operation in a diesel engine. MPC is a control method based on a predictive dynamic model of system and determines actuator control positions through the optimization of various factors such as tracking performances of target setpoints, moving speed of actuators, limits, etc. Previously, linear MPC has been successfully applied on the air path control problem of a diesel engine, however, most of these applications were developed for a single operation mode which has only one set of control target setpoint values. In reality, a single operation mode cannot cover all requirements of current diesel engines and this complicates practical implementations of linear MPC. The high priority targets for the development of diesel engines are low emissions, high thermal efficiency and robustness. These objectives require multi-mode operations such as a HP EGR (High pressure exhaust gas recirculation) mode in cold coolant condition, a Double EGR mode for sufficient EGR rates, a Diesel Particulate Filter (DPF) regeneration mode for the heat-up of exhaust gas temperature and a rich mode of exhaust gas for Lean NOx Trap (LNT) regeneration. Each engine operation mode requires different target setpoints from the air path, such as air mass flow rate and oxygen concentration. In the multi-mode operation, simple linearization based MPC is limited in the practical application because a linearization point changes depending on target setpoints of each operation mode. This means that a linear model for a specific operation mode is not valid in other operation modes, which have different target setpoints. Moreover, the modern diesel air path system is highly nonlinear and would require a significant number of linear models to adequately represent the entire behavior not only at all operation points of engine speed and load, but also at the various operation modes. In this study, a new scheme is proposed and tested on a diesel engine utilizing combined benefits of a supervisory MPC and component level nonlinear compensators. The developed nonlinear compensators are based on dynamic real-time inversions of individual component models. The control scheme comprises of three parts: a supervisory MPC as the coordination of target setpoints in high-level to achieve the objectives, a component level control of nonlinear compensator, state observation either by virtual sensor or by Electronic Control Unit (ECU) sensor. The test results from an engine test bench and a chassis dynamometer demonstrates that the proposed method works well in multi-mode operation and can be applied with the significant benefit that no mode specific control strategies and calibration are needed. A valuable benefit of this approach can be seen in the calibration effort, particularly during development when the setpoints are not necessarily fixed.

Nonlinear model predictive control(NMPC) of diesel oxidation catalyst (DOC) outlet temperature for active regeneration of diesel particulate filter (DPF) in diesel engine

Nonlinear Predictive Control of Diesel Engine DOC Outlet Temperature

A Thermal Management Strategy for Proton Exchange Membrane Fuel Cell via Nonlinear Model Predictive Control

Optimal control of Hydrocarbon Reducer (HC) injection based on Trust-Region-Reflective Algorithm (TRRA) and physical models for Diesel Oxidation Catalyst (DOC)

Study on Characteristics and Control Strategy of Diesel Particulate Filters Based on Engine Bench

Control-Oriented Modeling and Observer-Based Estimation of Solid and Gas Temperatures for a Diesel Engine Aftertreatment System

Nonlinear Model Predictive Control of Integrated Diesel Engine and Selective Catalytic Reduction System for Simultaneous Fuel Economy Improvement and Emissions Reduction

Model Predictive Control Case Study: Selective Catalytic Reduction (scr) System in Coal-Fired Power Plant

Combined feedforward and error-based active disturbance rejection control for diesel particulate filter thermal regeneration

Model predictive emissions control of a diesel engine airpath: Design and experimental evaluation

Model Predictive Control of an Air Path System for Multi-Mode Operation in a Diesel Engine

Multiobjective Optimization of Diesel Particulate Filter Regeneration Conditions Based on Machine Learning Combined with Intelligent Algorithms

A Study on the Compound Regeneration Control Strategy for DPF Using Burner and DOC

NO and NO2 Concentration Modeling and Observer-Based Estimation Across a Diesel Engine Aftertreatment System

Nonlinear model predictive control applied to multivariable thermal and chemical control of selective catalytic reduction aftertreatment

Experimental study on filtration and continuous regeneration of a particulate filter system for heavy-duty diesel engines.

Full course evolution characteristics of DPF active regeneration under different inlet HC concentrations

An Efficient Data-Driven Approach for Modeling and Optimization of Reactivity-Controlled Compression Ignition Engine Fueled with Polyoxymethylene Dimethyl Ethers and Hydrogen

Experimental Validation of Nonlinear Model Predictive Control for a Heavy-Duty Diesel Engine Waste Heat Recovery System

End-to-End Deep Neural Network Based Nonlinear Model Predictive Control: Experimental Implementation on Diesel Engine Emission Control

Experimental and Simulation Study on Diesel Spray Oxidation During Active Regeneration of DPF