Abstract:Due to the rapid development of the distribution network, there is an urgent need for high-precision state estimation and safe and stable operation, this paper proposes a joint optimal placement method for Phasor Measurement Unit (PMU) and Dual Use Line Relay (DULR) in distribution networks considering fault reconstruction and state estimation accuracy. The proposed method aims to minimize the cost of PMU and DULR configuration. Based on the known pseudo-measurements and Supervisory Control and Data Acquisition (SCADA) measurements, we use the E-optimal standard design of the state estimation error covariance matrix to form the state estimation accuracy index and take the relay protection function of Feeder Terminal Unit (FTU) device and DULR device into consideration of the fault reconstruction. By solving the mixed integer semidefinite programming (MISDP) model, the optimal placement result is obtained, so that the network under normal condition and the network after multiple fault reconstruction can meet the constraints of state estimation accuracy and load loss rate respectively. The proposed method is tested on IEEE 33-node, 123-node systems as an example. The experimental results show that the proposed method is effective and practical. Note to Practitioners— This study is stimulated by the need for optimizing the placement of Micro-PMU (μPMU) in distribution network. Since the new μPMU device DULR has the same relay protection function as FTU, and distributed generation can supply power to the island after failure, this paper adds the load loss rate to the constraint conditions to study the influence of fault reconstruction on the placement scheme. A new two-step SE method considering mixed measurements was used in this paper to improve the computational efficiency of real-time SE of large-scale system while ensuring the accuracy of the calculation results. We have conducted tests in IEEE-33 and IEEE-123 systems. After preliminary verification, compared with the single fault scenario, we find that the placement scheme considering multiple fault scenarios can effectively improve the accuracy of state estimation and reduce the load loss rate of each fault scenario and only increase the cost a little. The increase in the number of DG and contact lines in the network will also effectively improve the feasibility of the placement scheme. The increase of the number of FTU configurations can effectively reduce the configuration of DULR by adding a small amount of μ PMU, reduce the total cost as a result. In future studies, we will further consider the integrated configuration of μ PMU, DULR and FTU, to meet more failure scenarios while reducing costs.

Detection and Correction of PMU Angle Deviation for Double-Circuit Line Using Reactive Power Measurements

PMU Angle Deviation Detection and Correction Using Line Reactive Power Measurements

The Power Angle and Phase Measurement Units Based Wide Area Measurement System and Its Application

Single-phase-to-ground Fault Detection with Distributed Parameters Analysis in Non-Direct Grounded Systems

An Efficient PMU-Based Fault-Location Technique for Multiterminal Transmission Lines

Transmission Lines Positive Sequence Parameters Estimation and Instrument Transformers Calibration Based on PMU Measurement Error Model

PMU-Based Fault Location Using Voltage Measurements in Large Transmission Networks

Detection Method for Sub-synchronous and Super-synchronous Harmonic Phasors in Power System

State estimation for distribution systems using micro-synchrophasors

Network Parameter Identification and Estimation Based on Hybrid Measurement of WAMS/SCADA

Research on Fault Location Based on Dynamic Synchronous Phasor Measurement by PMU

High-Precision Analysis Using μPMU Data for Smart Substations

Optimal PMU Placement Approach for Power Systems Considering Non-Gaussian Measurement Noise Statistics

Augmented State Estimation of Line Parameters in Active Power Distribution Systems with Phasor Measurement Units

A Two-Terminal Fault Location Algorithm Using Asynchronous Phasors Based on Distributed Parameter Model

Field PMU Test and Calibration Method– Part I: General Framework and Algorithms for PMU Calibrator

Uneven Demagnetization Fault Diagnosis in Dual Three-Phase Permanent Magnet Machines Based on Electrical Signal Difference

Investigation of optimal PMU placement considering limited number of channels constraints and critical line constraints

Presenting a hybrid method for fault tolerance based on neural fuzzy logic in distribution networks using phasor measurement units

Joint optimal PMU and DULR placement in distribution network considering fault reconstruction and state estimation accuracy

Fault Location Technology for Power System Based on Information About the Power Internet of Things