Abstract:The new developed metal/composite co-cured material composed of carbon fiber–reinforced plastic and Al phases has been increasingly applied for manufacturing of attitude control flywheel in aerospace industry. However, drilling of co-cured material is still a challenging task to produce holes with high quality and low cost in the assembly chain and dynamic balance debugging of attitude control flywheel. In other words, the relevant mechanisms and experimental findings involved in the drilling process of carbon fiber–reinforced plastic/Al co-cured material is not clearly defined, which impedes the progress of attitude control flywheel production. To this end, this article specially addresses the experimental studies on the drilling process of carbon fiber–reinforced plastic/Al co-cured material with standard TiAlN-coated cemented carbide twist drill. The significance of this work aims to reveal the regardful cutting responses of the hole characteristics and tool wear modes during the practical drilling process of co-cured material. A full factorial experiment including three levels of feed rate and four levels of cutting speed was performed. The hole diameter shows different values in different positions while it indicates consistent pattern regardless of the cutting variables: the largest in the Al phase, followed by the upper and lower carbon fiber–reinforced plastic phases, respectively. Grooves and matrix degradation are the major machining defects for carbon fiber–reinforced plastic layers, while a great chip debris adhered to the machined surface is the case for Al layer. Subsequent wear analysis showed that abrasion was mainly maintained at the vicinity of major/minor cutting edges and drill edge corner, followed by chip adhesion on the chisel edge region. Carbide substrate of drill flank face is exposed, and thereafter cavities are formed under the strong mechanical abrasion. These results could provide several implications for industrial manufacturers during the attitude control flywheel production.

Low-frequency axial vibration drilling of Al2O3/GFRP laminated composite plate by diamond trepanning bit

A New Strategy of Carbon Fiber Reinforced Plastic Drilling Evaluation Using Thermal Measurement

Hole quality in longitudinal–torsional coupled ultrasonic vibration assisted drilling of carbon fiber reinforced plastics

Mechanism and feasibility study of low frequency vibration assisted drilling of a newly developed CFRP/Al co-cured material

A study on the ultrasonic vibration on the cutting performance during ultrasonic-assisted drilling of CFRP with twist and dagger drill bits

Experimental Study of Drilling Behaviors and Damage Issues for Woven GFRP Composites Using Special Drills

High-speed drilling mechanism study of unidirectional CoCrFeNiAl fiber-reinforced aluminum matrix composites

Study on the mechanism of AL2024-T351/Ti-6Al-4V laminated materials by ultrasonic vibration drilling

Effects of Specialized Drill Bits on Hoe Defects of CFRP Laminates

Hole quality and tool wear when dry drilling of a new developed metal/composite co-cured material

Wear Behavior of Special Tools in the Drilling of CFRP Composite Laminates

Wear behaviors of PCD and diamond-coated tools during low-frequency vibration-assisted drilling CFRP/Ti stacks

Wear behaviour of CVD diamond-coated tools in the drilling of woven CFRP composites

Experimental research on ultrasonic vibration countersinking process of CFRP composite laminates

Tool Wear Processes in Low Frequency Vibration Assisted Drilling of CFRP/Ti6Al4V Stacks with Forced Air-Cooling

Experimental Study on Drilling Process of a Newly Developed CFRP/Al/CFRP Co-Cured Material

Experimental Study on Longitudinal-Torsional Ultrasonic Vibration Drilling of Carbon Fiber–reinforced Plastics/titanium Alloy Stacks

The development of an ultrasonic vibration hand-held pneumatic drill for hole-machining on CFRP composite materials

Study on dynamic drilling forces of CFRP/Ti stacks during longitudinal-torsional ultrasonic vibration drilling

Study on the surface integrity of micro-holes in high volume fraction SiCp/Al using ultrasonic vibration drilling

Machinability Of Drilling T700/Lt-03a Carbon Fiber Reinforced Plastic (Cfrp) Composite Laminates Using Candle Stick Drill And Multi-Facet Drill