Abstract:Ultrasonic-assisted drilling (UAD) is a machining process that is known to improve the hole quality and reduce cutting forces. Previous studies focused on optimizing cutting parameters to improve the hole quality in conventional drilling (CD) and UAD, as well as to finding the optimum vibration parameters (frequency and amplitude) that will increase the effectiveness of the UAD process. However, the influence of cutting tool type during UAD has been largely overlooked. This research aims to address this gap by analyzing the effect of cutting tool type during UAD on the cutting forces and hole quality in GLARE (Glass Laminate Aluminum-Reinforced Epoxy) laminates. Four types of drills, namely, twist drill (TD), double cone drill (DCD), a step drill type 1 (SD1), and step drill type 2 (SD2) with different step length, were selected for this study. The lowest thrust force (47.04 N) and torque (0.079 Nm) were achieved using twist drill, while DCD, SD1, and SD2 exhibited higher thrust forces (12.81%, 20.69%, 41.3%) and torques (94%, 92%, 91%), respectively. In addition, TD produced high-quality holes with lowest surface roughness (R a 1.66 μm, R z 10.58 μm) and minimal burr formation (entry burr height 152.3 μm, exit burr height 69.22 μm). Conversely, DCD, SD1, and SD2 showed higher surface roughness R a (23%, 16%, 24%) and R z (16%, 37%, 29%), respectively, compared to the TD. Holes drilled using SD1 and SD2 generally had smaller burr height. Overall, UAD system effectively reduced cutting forces at low spindle speed and feed rate. To achieve higher drilling quality, specifically to reduce the surface roughness and exit burr height, a medium spindle speed of 3000 rpm, a feed rate of 225 mm/min is recommended. Drilling at higher cutting parameters using UAD resulted in a decline in hole quality, except for entry burr height.

Reducing cutting force in rotary ultrasonic drilling of ceramic matrix composites with longitudinal-torsional coupled vibration

Design of a Novel Air Bearing Workbench for Rotary Ultrasonic Drilling of Advanced Ceramics

Cutting force and specific energy for rotary ultrasonic drilling based on kinematics analysis of vibration effectiveness

Analytical and experimental investigation on cutting force in longitudinal-torsional coupled rotary ultrasonic machining zirconia ceramics

Experimental and Theoretical Investigation on Critical Cutting Force in Rotary Ultrasonic Drilling of Brittle Materials and Composites

Experimental study on vibration stability in rotary ultrasonic machining of ceramic matrix composites: Cutting force variation at hole entrance

Feasibility Study of Longitudinal–Torsional-Coupled Rotary Ultrasonic Machining of Brittle Material

Improving hole exit quality in rotary ultrasonic machining of ceramic matrix composites using a compound step-taper drill

Experimental and scale-span numerical investigations in conventional and longitudinal torsional coupled rotary ultrasonic–assisted drilling of CFRPs

Hole quality in longitudinal–torsional coupled ultrasonic vibration assisted drilling of carbon fiber reinforced plastics

An Experimental Study on Rotary Ultrasonic Drilling Small-Diameter Holes of High Volume Fraction Silicon Carbide-Reinforced Aluminum Matrix Composites (Sicp/al)

Experimental Study on Longitudinal-Torsional Ultrasonic Vibration Drilling of Carbon Fiber–reinforced Plastics/titanium Alloy Stacks

Study on tool wear in longitudinal-torsional composite ultrasonic vibration–assisted drilling of Ti-6Al-4V alloy

Investigations on the edge-chipping reduction in rotary ultrasonic machining using a conical drill

A study on the ultrasonic vibration on the cutting performance during ultrasonic-assisted drilling of CFRP with twist and dagger drill bits

Study on the mechanism and performance of longitudinal-torsional ultrasonic vibration assisted drilling CFRP/Ti stack

Study on chip shapes in longitudinal-torsional composite ultrasonic vibration–assisted drilling of Ti-6Al-4V

Study on the mechanism of AL2024-T351/Ti-6Al-4V laminated materials by ultrasonic vibration drilling

Influence of cutting tool design on ultrasonic-assisted drilling of fiber metal laminates

Preliminary Investigation on Rotary Ultrasonic Face Milling of Ceramic Matrix Composite C/Sic: Design of Experiments

Development of A Novel Ultrasonic Drill Using Longitudinal-Bending Hybrid Mode