Abstract:Two-dimensional (2D) metal halide perovskites have recently emerged as promising photovoltaic materials due to their superior ambient stability and rich structural diversity. However, power conversion efficiencies (PCEs) of the 2D perovskites solar cells (PSCs) still lag behind their three-dimensional (3D) counterpart, particularly due to the anisotropy in the charge carrier mobility and inhomogeneous energy landscape. A promising alternative is Dion-Jacobson (D-J) phase quasi-2D perovskite, where the bulky organic diammonium cations are introduced into inorganic frameworks to remove the weak van der Waals interactions between interlayers and to improve the open-circuit voltage (Voc). Although the D-J phase 2D perovskite shows a homogeneous energy landscape and better charge transport, their poor crystallinity and existence of higher trap states remain a major challenge for the development of high-efficiency solar cells device. To address this issue, here, we report the eclipsed D-J phase 2D perovskite using 1,5-diaminonaphthalene cation and subsequently treated the film with ammonium thiocyanate (NH4SCN) additive to further improve the film crystallinity, out-of-plane orientation, and carrier mobility. We observe that 2 mol NH4SCN surface treatment in NDA-based D-J phase perovskite leads to better film morphology and improved crystallinity, as confirmed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Time-resolved photoluminescence (TRPL) spectroscopy and steady-state space charge limited current (SCLC) mobility measurement reveal a significant reduction of trap-assisted nonradiative recombination and improvement of carrier mobility in the thiocyanate-passivated perovskite. Consequently, the PCE of the NH4SCN-treated (NDA)(MA)3(Pb)4(I)13 perovskite device enhanced nearly 46% from 10.3 to 15.08%. We have further studied intensity-dependent J-V characteristics, which demonstrate the reduction of ideality factor, confirming the effective suppression of trap-assisted nonradiative recombination, consistent with the transient PL results. Electrochemical impedance spectroscopy (EIS) confirms the improved charge carrier transport in NH4SCN additive-treated devices. Interestingly, our additive-engineered unsealed perovskite devices retained 75% of their initial efficiency after 1000 h of continuous storage under 60% relative humidity. This study opens up the strategy for developing high-efficiency and stable 2D perovskite solar cells.

The Effect of the Alkyl Chains of the Alkylammonium Pesudohalide Additives on the Performance of Dion Jacobson Perovskite Solar Cells

Methylammonium Chloride as a Double‐Edged Sword for Efficient and Stable Perovskite Solar Cells

The Effect of Methyl Ammonium Chloride Doping for Perovskite Solar Cells on Structure, Crystallization and Power Conversion Efficiency

Methylammonium Chloride or Guanidinium Chloride As an Additive to Improve Performance of 2D Alternating Cation Perovskite Solar Cells: A Direct Comparison

Methylammonium Acetate As an Additive to Improve Performance and Eliminate J-V Hysteresis in 2D Homologous Organic-Inorganic Perovskite Solar Cells

Effects of Methylammonium Acetate on the Perovskite Film Quality for the Perovskite Solar Cell

Thiocyanate-Passivated Diaminonaphthalene-Incorporated Dion-Jacobson Perovskite for Highly Efficient and Stable Solar Cells

Stabilizing formamidinium lead triiodide α-phase with diamine cations for perovskite solar cells

Methylammonium Chloride Additive in Lead Iodide Optimizing the Crystallization Process for Efficient Perovskite Solar Cells

Compositional and Solvent Engineering in Dion–Jacobson 2D Perovskites Boosts Solar Cell Efficiency and Stability

Methylammonium thiocyanate seeds assisted heterogeneous nucleation for achieving high-performance perovskite solar cells

Unraveling Differences in the Effects of Ammonium/Amine-Based Additives on the Performance and Stability of Inverted Perovskite Solar Cells

The Synergistic Effect of Additives for Formamidinium-Based Inverted Dion-Jacobson 2D Perovskite Solar Cells with Enhanced Photovoltaic Performance

Synergistic effect of MACl and DMF towards efficient perovskite solar cells

Bimolecular Crystallization Modulation Boosts the Efficiency and Stability of Methylammonium‐Free Tin–Lead Perovskite and All‐Perovskite Tandem Solar Cells

Additive-Induced Film Morphology Evolution for Inverted Dion–Jacobson Quasi-Two-Dimensional Perovskite Solar Cells with Enhanced Performance

Homogenizing Morphology and Composition of Methylammonium‐Free Wide‐Bandgap Perovskite for Efficient and Stable Tandem Solar Cells

Ammonium Sulfate to Modulate Crystallization for High-Performance Rigid and Flexible Perovskite Solar Cells

The Molecular Additive N-Acetyl-L-Phenylalanine Delays the Crystallization and Suppresses the Phase Impurity for Achieving Triple-Cation Perovskite Solar Cells with Efficiency over 25.

Synergetic Effect on Enhanced Photovoltaic Performance of Spray-Coated Perovskite Solar Cells Enabled by Additive Doping and Antisolvent Additive Spraying Treatment

Ethylenediamine Addition Improves Performance and Suppresses Phase Instabilities in Mixed-Halide Perovskites