Abstract:We present a solid‐state processing pathway for ultrahigh molecular weight polyethylene, a high‐end engineering polymer that cannot be melt processed. Ultra‐high molecular weight polyethylene (UHMWPE) stands out as the preferred material across a wide spectrum of demanding applications, thanks to its remarkable mechanical, chemical and physical attributes. Nevertheless, processing UHMWPE can be an arduous and time‐consuming endeavor. Traditional melt‐processing techniques, commonly employed for polymers, prove impractical due to the exceedingly high viscosity of the melt that follows from the highly entangled macromolecular chains. Several methods are known to lower the entanglement density of UHMWPE, such as crystallization from a semidilute solution or direct polymerization, resulting in a less interconnected polymer structure. Unfortunately, even with low‐entangled UHMWPE, melt processing remains unviable because of the rapid re‐entanglement of polymer chains upon melting. However, these low‐entangled UHMWPE materials can still be effectively processed in the solid state, a technique employed in the production of high‐performance UHMWPE fibers and tapes, currently the only two feasible geometries. This research reports the development of a solid‐state extrusion method for nascent low‐entangled powder, centering on manipulating the surface energy of the interior wall materials within the extruder and die. Ordinary steel dies proved ineffective for solid‐state extrusion, as they generated excessive friction between the die and UHMWPE, resulting in a rapidly escalating extrusion pressure. However, utilizing dies constructed from temperature‐resistant polymers allowed for extrusion at a consistent pressure without the need for lubricating agents. We demonstrate the practicality of the developed solid‐state extrusion method by fabricating UHMWPE monofilaments and tubes, showcasing its potential in expanding the range of producible UHMWPE geometries. Additionally, a first evaluation of the influence of processing conditions and the entanglement density of the reactor powder used on extrudability, and the properties of the resulting components is presented. Highlights A process for the solid‐state extrusion of UHMWPE is developed. UHMWPE processing with higher design flexibility than current industrial standards. UHMWPE processing with higher throughput than current industrial standards. Contrary to previous techniques no lubricating agent or co‐extrudate is used.

A Universal Strategy for Rapid and Scalable Surface Modification of Ultra High Molecular Weight Polyethylene Fiber

Synergistically improving interface behavior by designing physical twisting structure and "rigid-flexible" interface layer on ultra-high molecular weight polyethylene (UHMWPE) fiber surface

Interfacial Welding of Dynamic Covalent Network Polymers

Enhanced Interfacial Properties of High-Modulus Carbon Fiber Composites Via Molecular Assembly on Fiber Surface

Improvement of UHMWPE Fibers Interfacial Properties by Aminosilane/silica Synergistic Modification

"Like binding a book": Interfacial improvement of pre-melted ultrahigh molecular weight polyethylene by pulse vibration molding

Superior Enhancement of the UHMWPE Fiber/Epoxy Interface through the Combination of Plasma Treatment and Polypyrrole In-Situ Grown Fibers

Surface modification of ultra‐high molecular weight polyethylene fiber by different kinds of SiO2 nanoparticles

Research progress on surface modification and application status of UHMWPE fiber

Remarkably improved interfacial adhesion of UHMWPE fibers reinforced composite by constructing a three-dimensional stacked nanoparticles structure at interphase

Excellent interfacial bonding in UHMWPE fiber/ epoxy resin composites fabricated via a swelling approach

A Comprehensive Review of Ultrahigh Molecular Weight Polyethylene Fibers for Applications Based on Their Different Preparation Techniques

Simultaneous Improvements in Wear Resistance and Mechanical Properties of Uhmwpe Nanocomposite Fabricated Via A Facile Approach

Study of UHMWPE Fiber Surface Modification and the Properties of UHMWPE/Epoxy Composite

Bio-inspired copper ion-chelated chitosan coating modified UHMWPE fibers for enhanced interfacial properties of composites

Solid‐state extrusion of nascent disentangled ultra‐high molecular weight polyethylene

Surface Modification and Dyeing of Ultrahigh-Molecular-Weight Polyethylene Fabrics Using Diazirine-Based Polymers

Fast and Integral Nano-Surface-Coating of Various Fiber Materials via Interfacial Polymerization

Soluble Polyimide Coated UHMWPE Fibers with Multiple Property Enhancements: Surface Activity, Tensile Strength, Heat Resistance, Acid Resistance, and Erasability

Enhancing the Interfacial Property Between UHMWPE Fibers and Epoxy Through Polydopamine and SiO2 Surface Modification

A novel PDA/POSS transition layer on the surface of UHMWPE fibers by co-depositing to improve the mechanical properties of composites