Abstract:Total knee arthroplasty (TKA) is a cornerstone in addressing knee joint disorders, significantly enhancing patients' quality of life. However, despite technological advancements, a comprehensive understanding of the dynamic stresses experienced by knee prostheses during daily activities, particularly under rehabilitation interventions, remains elusive. This study aims to bridge this gap by employing numerical simulations and finite element analysis to elucidate these dynamic stresses and their interaction with rehabilitation protocols. A real-life knee replacement prosthesis model was meticulously constructed through coordinate measuring and 3D scanning, facilitating detailed finite element analysis in ANSYS Workbench version 17.1. Two distinct boundary conditions and loading scenarios were applied, with comparisons made between linear and nonlinear material assumptions. The simulation results using these different boundary condition methods revealed minimal differences. Specifically, at a knee angle of 0°, the relative stress error rate between the two boundary condition types was approximately 1 % (1.11 MPa and 1.099 MPa, respectively). At 15° and 90°, the error rates were 1.9 % and 0.56 %, respectively (10.275 MPa and 10.078 MPa at 15°; 10.275 MPa and 10.078 MPa at 90°). Given these minimal differences, the first type of boundary condition was adopted for the subsequent scenarios to enhance convergence efficiency in the analysis. Moreover, comparative analyses between linear and nonlinear material behaviors demonstrated acceptable agreement, offering insights into potential efficiency gains in simulation methodologies. Building on this foundation, an optimized tibial model was proposed, incorporating geometric alterations to the tray. Quantitative assessments revealed significant reductions, with von Mises stress decreasing by 23.35 % and equivalent strain by 17 % at a knee angle of 140°. Further evaluations at varying angles, including 60°, consistently showed positive influences on stress and strain. These quantitative findings not only contribute valuable insights into the mechanical behavior of knee prostheses but also provide tangible evidence for the efficacy of linear material behavior assumptions. The proposed optimized model exhibits promising potential for enhancing the design and performance of knee prostheses, particularly under critical loading conditions. In conclusion, these results underscore the importance of a nuanced understanding of knee prosthesis behavior during rehabilitation, offering a quantitative foundation for refining existing designs and informing the development of next-generation prostheses.

Soft tissue elasticity in total knee arthroplasty: An in vivo quantitative analysis

Can Intraoperative Intra-Articular Loads Predict Postoperative Knee Joint Laxity Following Total Knee Arthroplasty? A Cadaver Study with Smart Tibial Trays

A New System for Soft-Tissue Balance Measurement in Total Knee Replacement

A Method for Dynamically Measuring the Soft Tissue Balance in the Total Knee Replacement

Measurement of femoral posterior condylar offset and posterior tibial slope in normal knees based on 3D reconstruction

R&D of a dynamical soft tissue balance measurement device for knee arthroplasty

Development of Soft Tissue Balance System and Its Application for Quantitative Knee Collateral Ligament Release: an Experimental Study

Correlation Between Femorotibial Pressure and Joint Gap in Osteoarthritis Patients with Varus Deformity: an Intraoperative Measurement Using Sensor Device in Primary Posterior-Stabilized Total Knee Arthroplasty

Achieving Specified Laxity In A Non-Cruciate Total Knee: A Laboratory Design Study

In Vitro Kinematic Measurements of the Patellar Tendon in Two Different Types of Posterior-Stabilized Total Knee Arthroplasties

Intraoperative loose flexion gap may restrict postoperative knee flexion after J-curve design posterior-stabilized total knee arthroplasty

Association of intraoperative medial joint gap laxity in the flexion position with subjective knee instability after fixed-bearing posterior-stabilised total knee arthroplasty

Combined measurement and modeling of specimen-specific knee mechanics for healthy and ACL-deficient conditions

An electronic force sensor accurately detects increased but not decreased soft tissue tension in total knee arthroplasty

Intraoperative identification of patient-specific elastic modulus of the meniscus during arthroscopy

Impact of Structural Compliance of a Six Degree of Freedom Joint Simulator on Virtual Ligament Force Calculation in Total Knee Endoprosthesis Testing

Numerical investigation of knee prosthesis stresses in daily activities: Insight into knee rehabilitation and Creation of a new optimal model

Site-specific elastic and viscoelastic biomechanical properties of healthy and osteoarthritic human knee joint articular cartilage

Finite Element Analysis and Mechanical Assessment for the Constraint of Total Knee Replacement

A New Methodology for the Accurate Measurement of Tibiofemoral Kinematics in Human Cadaveric Knees: An Evaluation of the Anterior–Posterior Laxity Pre- and Post-Cruciate Ligament Resection

Multiscale Correlations between Joint and Tissue-Specific Biomechanics and Anatomy in Postmortem Ovine Stifles