Abstract:Injection molding is widely used for the mass production of plastic components. However, an appropriate choice of the process parameters is essential to ensure the precision and uniformity of the molded parts. The flow length-to-wall thickness (L/t) ratio for most molded components lies in the range of 100∼200. For higher values of the L/t ratio, the flow resistance increases dramatically at the end of the molded part and the injection pressure propagates less easily through the mold cavity. Consequently, the geometric dimensions of the molded parts in the near-gate region are frequently different from those in the far-from-gate region as well as resulting in lower uniformity. In practice, the variation in the geometric dimensions is significantly dependent on the filling-to-holding (V/P) switchover point, injection speed, and holding condition. Accordingly, the present study commences by proposing a simple least-squares regression-based approach for determining the appropriate V/P switchover point based on the quality requirement for the geometric dimensions of the molded component. In addition, a multi-stage holding condition is used to improve the geometric uniformity of the molded component by minimizing the residual pressure difference between the near-gate and far-from-gate regions of the mold at the end of the packing stage. Finally, a deceleration strategy is considered for the injection screw at the end of the filling stage to further reduce the quality variation. The experimental results show that for molded components with a large L/t ratio, the V/P switchover point should be determined based on the quality requirement for the part in the far-from-gate region in order to avoid insufficient quality compensation in the early holding stage. Furthermore, compared with the single-stage holding condition, the multi-stage holding condition reduces the residual pressure difference between the near-gate and far-from-gate regions of the cavity by around 74.5% (from 48.7 to 12.5 MPa). As a result, the difference in width between the near-gate region of the molded component and the far-from-gate region is reduced by about 66.7% (0.09 to 0.03 mm), while the difference in thickness is reduced by approximately 32.1% (0.028 to 0.019 mm). The deceleration strategy for the injection screw has no noticeable effect on the quality uniformity of the molded part provided that the V/P switchover point and multi-stage holding pressure are appropriately designed.

Cavity pressure‐based holding pressure adjustment for enhancing the consistency of injection molding quality

Enhancing the quality stability of injection molded parts by adjusting V/P switchover point and holding pressure

Influence of V/P switchover point, injection speed, and holding pressure on quality consistency of injection‐molded parts

Determination of process parameters based on cavity pressure characteristics to enhance quality uniformity in injection molding

Research on Quality Characterization Method of Micro-Injection Products Based on Cavity Pressure

Cavity Pressure Control During the Cooling Stage in Thermoplastic Injection Molding

Effect on Residual Wall Thickness of Parts with Floating Core Injection of Water-Assisted Injection Molding

Simulation and Experimental Analysis on Non-circular Cross-section Parts Residual Wall Thickness of Water-assisted Injection Molding

A Closed-Loop Multivariable Quality Control Scheme for Injection Molding Process

Cavity Pressure Dynamics and Self‐tuning Control for Filling and Packing Phases of Thermoplastics Injection Molding

Strategies for adjusting process parameters in CAE simulation to meet real injection molding condition of screw positions and cavity pressure curves

Two-stage dynamic adjustment strategy for weight consistency improvement in injection molding process

Effective fast-response pressure control for thin-wall gas-assisted injection molding

Optimize Injection-Molding Process Parameters and Build an Adaptive Process Control System Based on Nozzle Pressure Profile and Clamping Force

Non-destructive measurement of cavity pressure during injection molding process based on ultrasonic technology and Gaussian process

Optimization of clamping force for low-viscosity polymer injection molding

Self‐tuning Cavity Pressure Control of Injection Molding Filling

Out-of-Mold Sensor-Based Process Parameter Optimization and Adaptive Process Quality Control for Hot Runner Thin-Walled Injection-Molded Parts

Fast prediction of crystallinity in injection molding during the packing stage

Part weight control via model free optimization for injection molding

On-line measurement of cavity pressure during injection molding via ultrasonic investigation of tie bar