Abstract:Pressurized water reactors (PWRs) are employed worldwide and continue to expand in capacity. They require thorough investigation, particularly concerning their safety and operational efficiency. To ensure these factors, comprehensive research into their various components and an understanding of the diverse phenomena they experience within a PWR are imperative. These phenomena can be of mechanical, thermal, hydraulic, or neutronic nature. Among these components, fuel assemblies (FAs) hold a main role in PWRs. The intricate interplay of these physical factors results in the modification of FAs geometry, specifically permanent elongation and lateral deformations referred to as irradiation creep. The earliest reported occurrence of these deformations dates back to 1994 in Ringhals reactors, where various FAs exhibited distinct deformations (Andersson et al., 2005). Given that these phenomena occur over a time span of months to years in metallic materials, conducting investigations within the confines of a typical laboratory observation period becomes impractical. Consequently, this project proposes an alternative experimental methodology to overcome this challenge, thus gaining a deeper understanding of the fluency phenomenology in FAs behavior. This methodology consists on the design of a reduced-scale test section, capable of replicating the fluid–structure interaction (FSI) responsible for creep, the creation of spacer grids through 3D printing technology, and selection of the appropriate material for the fuel rods (FRs), with an emphasis on macroscopic coupling effects, rather than focusing into the micro-structural response of the material. To experimentally observe the deformation on the FAs, cameras were used to capture images through the time during the test, to catch the displacement of the FRs. The first results showed the mock-up was able to reproduce the FSI causing the creep on the FAs, it was possible to capture the displacement evolution along time, and to observe different types of deformation, thus, it helps to understand the phenomenon. Further tests and investigations using laser doppler velocimetry (LDV) technique to analyze the flow will be held, to a better comprehension of these burden.

Development of a Cyclic Creep Testing Station Tailored to Pressure-Sensitive Adhesives

An Exploratory Study on Determining and Modeling the Creep Behavior of an Acrylic Pressure-Sensitive Adhesive

Predictive Mechanistic Model of Creep Response of Single-Layered Pressure-Sensitive Adhesive (PSA) Joints

Tensile and Shear Creep Behavior of Structural Adhesives: Experiments and Modeling

Creep Behaviour and Tensile Response of Adhesively Bonded Polyethylene Joints: Single-Lap and Double-Strap

Creep Behavior and Lifetime Prediction of PMMA Immersed in Liquid Scintillator

Experimental method for creep characterization of polymeric foam materials in media immersion

Customized High-Temperature Bending with DIC for High-Throughput Determination of Creep Parameters: Technique, Instrumentation, and Optimization

Analysis of creep crack growth in bonded joints based on a Paris' law-like approach

Interfacial fatigue fracture of pressure sensitive adhesives

Residual Life Assessment of In-Service High Temperature Components by Small Punch Creep Test

Creep Simulation and Validation for a Finite Element Analysis of Expanded Polystyrene-Based Cushioning Systems

Predictive mechanistic model for single-layered pressure-sensitive adhesive (PSA) joints

Fracture Analysis of Highly Flexible Adhesives: Cohesive Zone Modelling across a Wide Spectrum of Temperatures and Strain Rates

Development and Evaluation of Generic Test Pieces for Creep Property Assessment of Laser Powder Bed Fusion Components

Application of the Small Punch Creep-Recovery Test (SPCRT) for the Estimation of Large-Amplitude Viscoelastic Properties of Polymers

Creep damage laws for bonded joints under pure mode I loading

Experimental approach for measuring the peeling strength of a sheet bonded on a curved adherend with pressure sensitive adhesive and predicting the peeling resistance by finite element analysis

Double-Sided Pressure-Sensitive Adhesive Materials under Human-Centric Extreme Environments

Mock-up conception for experimentally investigate the creep phenomenon caused by the fluid–structure interaction in a rod bundle

Creep Damage Laws for Bonded Joints under Pure Mode II Loading