Abstract:Nowadays, adhesively bonded joints constitute an emergent area, being applied in several industries, especially in the aviation sector. Research has been developed on the analysis of the mechanical behaviour of bonded joints, while establishing fracture characterisation in pure modes I and II, and in mixed-mode I + II. Despite of the significant developments in analysing of bonded joints under quasi-static and fatigue conditions, few studies have addressed other mechanical phenomena such as creep. On creep analysis, developments have been presented on damage modelling of metallic materials, including the use of cohesive zone modelling (CZM). This study presents an adaptation of the Kachanov-Rabotnov and Liu-Murakami damage models, including rheological parameters by using Maxwell, Voigt-Kelvin, and Burgers constitutive equations when creep loading is considered. Other stress degradation effects due to creep phenomena are also considered, incorporating power law and sin-hyperbolic based models. Twelve damage models are derived: Kachanov-Rabotnov-Maxwell (KRM), Kachanov-Rabotnov-Voigt-Kelvin (KRVK), Kachanov-Rabotnov-Burgers (KRB), Kachanov-Rabotnov-Maxwell-Sun (KRMS), Kachanov-Rabotnov-Voigt-Kelvin-Sun (KRVKS), Kachanov-Rabotnov-Burgers-Sun (KRBS), Liu-Murakami-Maxwell (LMM), Liu-Murakami-Voigt-Kelvin (LMVK), Liu-Murakami-Burgers (LMB), Liu-Murakami-Maxwell-Hyperbolic (LMMH), Liu-Murakami-Voigt-Kelvin-Hyperbolic (LMVKH), and Liu-Murakami-Burgers-Hyperbolic (LMBH). Resulting damage laws are appropriate for adhesives, but also for ductile polymers in general. The implementation of the derived laws in CZM was demonstrated, being capable of modelling primary, secondary, and tertiary creep phases under pure mode I loading. A parametric analysis was also performed, assessing the level of creep damage rate induced by each parameter and their effect on the creep curve shape. A theoretical basis was established in this study for further analysis of creep loaded adhesively bonded joints using CZM, where mixed-mode I + II can be considered in the future.

Creep Damage Laws for Bonded Joints under Pure Mode II Loading

Creep damage laws for bonded joints under pure mode I loading

Evaluation of the cracked lap shear test for mixed-mode fracture toughness estimation of adhesive joints

Analysis of creep crack growth in bonded joints based on a Paris' law-like approach

Viscoelastic Bilinear Cohesive Model and Parameter Identification for Failure Analysis of Adhesive Composite Joints

Estimation of CZM Parameters for Investigating the Interface Fracture of Adhesively Bonded Joints Under Mode I, Mode II, and Mixed‐Mode (I/II) Loading

Estimation of Crack Tip Position in Adhesively Bonded Joints Subjected to Mode II Fatigue Loading

Identification of the Cohesive Parameters for Modelling of Bonded Joints between Flat Composite Adherends with Thick Layer of Adhesive

A Modified Microstructure-Based Creep Damage Model for Considering Prior Low Cycle Fatigue Damage Effects

Effect of strain-rate and moisture content on the mechanical properties of adhesively bonded joints

Numerical Analysis on the Bond Performance of Different ‎anchored Joints under Monotonic and Cyclic Pull-push Loading

Creep Behaviour and Tensile Response of Adhesively Bonded Polyethylene Joints: Single-Lap and Double-Strap

Influence of Loading Rate on the Cohesive Traction for Soft, Rubber-like Adhesive Layers Loaded in Modes I and III

Estimating crack tip position in adhesively bonded joints subjected to mode II quasi‐static loading

Estimation of fracture behavior of CFRP/CFRP adhesively bonded joints under mixed-mode conditions using a cohesive zone model

Modeling Of Non-Stationary Creep Processes Under Multiple Loading Conditions By Taking Into Account Damage Accumulation In A Structural Material

Mode II fatigue characteristics of a composite bonded joint with microstructured adhesive bondline through tailored sacrificial cracks

Modelling of Creep and Plasticity Deformation Considering Creep Damage and Kinematic Hardening

Influence of Failure-Load Prediction in Composite Single-Lap Joints with Brittle and Ductile Adhesives Using Different Progressive-Damage Techniques

New Model for Creep Damage Analysis and Its Application to Creep Crack Growth Simulations

Mechanical Performance of Adhesive Connections in Structural Applications