Abstract:In order to solve the problem of complicated electrochemical machining and unpredictable moulding morphology of shaped hot forging model cavities, this paper takes the "T" shaped cavity made of 40CrNiMoV as the research object. Firstly, the electrolyte formulation development test was carried out for 40CrNiMoV material, and the most suitable electrolyte formulation was selected as 8%NaCl + 11%NaNO 3 composite electrolyte through the measurement and analysis of the polarisation characteristic curve. Secondly, a multi-physical field coupling simulation model of electric field, gas–liquid two-phase flow field, temperature field and structural field is established, and based on the COMSOL software, the flow rate, temperature and bubble rate of electrolyte under different process parameters affect the law of anode surface forming accuracy, and the simulation results show that when the inlet pressure is low, the gap electrolyte flow rate of less than 5 m/s is larger, and it is easy to produce the phenomenon of passivation, which will lead to the temperature and bubble cannot be discharged in time, making the forming accuracy lower; in the electrolytic processing of the cavity bubble rate compared to the temperature has a greater impact on the conductivity, accompanied by the voltage increases, more heat and bubbles are generated in the processing gap, making the cavity forming accuracy worse; higher cathode feed rate can effectively improve the taper of the cavity side wall, so the cathode side wall insulation can avoid excessive corrosion of the non-processing surfaces, and the processing accuracy is significantly improved compared to the uninsulated. Therefore, insulating the cathode side wall can avoid excessive corrosion on the non-machining surface and improve the machining accuracy significantly. Finally, validation tests were carried out to obtain the measured values of the non-planar "T" shaped cavity inner wall profile and to compare the theoretical values of the simulation. The results show that the theoretical values of the coupled multi-physical field simulation are close to the measured values and can simulate the actual electrolytic process more accurately, providing a technological reference for the electrolytic machining of complex-shaped cavities.

The microstructure formation of thick Zr-based amorphous alloy with anode vibration in HClO4 solution by WECMM

Electrochemical micromachining of ZrCu-based amorphous alloy in ethylene glycol solution

Experimental Study of High-Frequency Vibration Assisted Micro/Mesoscale Forming of Metallic Materials

Effects of superimposed high-frequency vibration on deformation of aluminum in micro/meso-scale upsetting

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Exploring Electrochemical Direct Writing Machining of Patterned Microstructures on Zr702 with Polyacrylamide Polymer Electrolyte

Microfabricating Mirror-like Surface Precision Micro-Sized Amorphous Alloy Structures Using Jet-ECM Process

Anodic Dissolution Behavior of a Zr-based Bulk Metallic Glass and the Electrochemical Machining of Small Structures with High Geometrical Precision and Good Surface Quality

Enhancement of wire electrochemical micromachining of 40CrNiMoA with electrolyte ultrasonic assistance

Investigation of the microhole arrays generated by masked jet electrochemical machining with polyaluminum chloride electrolyte

Ultrasonic elliptical vibratory nanocutting mechanisms of Cu 50 Zr 50 amorphous alloy: A molecular dynamics simulation

Wire electric discharge machining and its effect on the surface finish of HfNbTaTiZr refractory high-entropy alloy

Research on Chemical Mechanical Polishing Technology for Zirconium-Based Amorphous Alloys

Achieving fully equiaxed grain microstructure and isotropic mechanical properties in wire arc additive-manufactured Mg-Y-Nd-Zr alloys

The dissolution characteristics and wire electrochemical micromachining of metallic glass Ni82Cr7Si5Fe3B3

On the WEDM of WNbMoTaZr x (x = 0.5, 1) Refractory High Entropy Alloys

Experimental study on the evolution process of Zr702 microdimple array generated with masked jet electrochemical machining

Nanocutting mechanisms of Cu50Zr50 amorphous alloy: A molecular dynamics simulation

Study on the forming law of ECM of non-planar "T" shaped cavities based on multi-physical field coupling

Wire Electrochemical Machining with Pulsating Radial Electrolyte Supply and Preparation of Its Tube Electrode with Micro-Holes

Wire arc additive manufacturing of a novel ATZM31 Mg alloy: Microstructure evolution and mechanical properties