Abstract:The study investigates the role of gas aspiration in shroud on steelmaking tundish performance. The tundish performance is adversely under the presence of gas aspiration. Additionally, under the higher gas loading ratio the pouring box's shape and design becomes redundant. Further, to improve the tundish performance, weirs have been used. Gas aspiration through ladle shroud, during the teeming of a ladle into a tundish, has been investigated via physical and mathematical modeling. To this end, a volume of fluid‐based two‐phase turbulent flow model (in conjunction with the standard k–ε turbulence model) and a full‐scale two‐strand bloom casting tundish have been applied. Both flow and residence time distribution measurements are carried out in the full‐scale tundish system, adopting well‐established measurement techniques. Computational results, supported appropriately with experimentally measured data, indicate that gas aspiration alters flow and turbulence profoundly in the vicinity of the shroud entry zone. Early reversal of jetting flow toward the free surface, due to the buoyancy of the entrained gas, increases the overall intensity of motion in the tundish, creating more mixing flow volumes at the expense of plug flow volume. Most importantly, however, gas aspiration through shroud tends to drastically cut down interactions between the down coming liquid jet metal and the pouring box, making the specific design and shape of a pouring box redundant toward desirable flow modification. Finally, it is shown that strong surface flows and turbulence, generated due to gas aspiration, can be suitably damped by deploying a set of weirs, increasing plug flow volume in tundish.

Continuous Casting Tundish Dead Volume Study by Physical Modeling and Computational Investigation

Design Improvement of Four-Strand Continuous-Casting Tundish Using Physical and Numerical Simulation

Analysis model of internal residence time distribution for fluid flow in a multi-strand continuous casting tundish

Experimental and Simulation Analysis of Physical Water Model through Tracer Injection under Various Baffles and Turbulence Inhibitor Conditions for Developing the Fluid Flow Parameters and Inclusion Removal Rates in Tundish

Study of Flow Characteristics of Tundish Based on Digital Image Velocimetry Technique

ESTABLISHMENT OF A FULL SCALE TUNDISH PHYSICAL SIMULATION PLATFORM AND APPLICATION RESEARCH

Flow Characteristics for Two-Strand Tundish in Continuous Slab Casting Using PIV

Simulation of Fluid Flow and Inclusion Removal in Five-Flow T-Type Tundishes with Porous Baffle Walls

Role of Gas Aspiration through Ladle Shroud and Influence on Tundish Hydrodynamic Performances: A Physical and Mathematical Modeling Study

Numerical Investigation on Motion and Removal of Inclusions in Continuous Casting Tundish with Multiorifice Filter

Mathematical Modeling of Transient Submerged Entry Nozzle Clogging and Its Effect on Flow Field, Bubble Distribution and Interface Fluctuation in Slab Continuous Casting Mold

Numerical Simulation of the Flow Field in an Ultrahigh-Speed Continuous Casting Billet Mold

Numerical Simulation on Refractory Wear and Inclusion Formation in Continuous Casting Tundish

On the Ladle Shroud Design and Mis-alignment Effects on the Fluid Flow in a Metallurgical Tundish- A CFD Model Study

Continuous Casting Mould for Square Steel Billet Optimised by Solidification Shrinkage Simulation

Investigation of Solidification, Heat Transfer and Fluid Flow in Continuous Casting of Steel Using an Advanced Modeling Approach

Study on Parameter Optimization of Diversion Wall in an Eight-Strand Tundish during Continuous Casting of Billet with High Casting Speed

Hydraulic and Numerical Simulation of Flow Field Characteristics in Induction Heating Continuous Casting Tundish

Three-Dimensional Fem Study of Fluid Flow in Mould for Beam Blank Continuous Casting: Influence of Straight Through Conduit Type Sen

Modeling Asymmetric Flow in the Thin‐Slab Casting Mold Under Electromagnetic Brake

Numerical Investigation on Transient Flow and Inclusion Removal Behavior in Tundish During Ladle Change Process