Abstract:This study aims to investigate the effect of tundish level control on the change in element content and inclusion amount in molten steel during the low tundish-level steel grade transition. Based on multiphase flow, mass transfer, and discrete phase, a three-dimensional transient numerical simulation of the tundish was established in Ansys Fluent. The model uses moving mesh refinement technology to obtain clear steel and slag interface with a small number of meshes. The numerical simulation results were verified through industrial experiments and physical simulations. The results indicate that when the tundish is at a low level, strand 3 becomes a short-circuit flow, and the number of inclusions in strand 3 is approximately four times that in strand 1. If the old grade density is higher than that of the new grade, the unqualified length of the element content in the transition billet is 10.2 m shorter than that in the opposite order. When the filling speed of the tundish is three times the normal flow rate, the length of the transition billet with an unqualified number of inclusions is 7.1 m less than that when the filling speed is 2 times the normal flow rate. In addition, at the initial stage of the low tundish level steel grade transition, the minimum amount of inclusions in the transition billet can be reduced to 40% of the average amount of inclusions in the old grade; however, the maximum number of inclusions in the transition billet increase by a factor of 2.5 times the average number of inclusions in the new grade at the end stage of the low tundish-level steel grade transition. It can be observed that the inclusions in the initial stage of the low tundish-level steel grade transition have less effect on the quality of the old grades; however, they have a greater effect on the new grades in the final stage of the low tundish-level steel grade transition.

Numerical Investigation on Transient Flow and Inclusion Removal Behavior in Tundish During Ladle Change Process

Numerical modeling of grade mixing and inclusion entrapment in eight strand billet tundish

Effect of Ladle Changeover Condition on Transient Three-Phase Flow in a Five-Strand Bloom Casting Tundish

Simulation of Fluid Flow and Inclusion Removal in Five-Flow T-Type Tundishes with Porous Baffle Walls

Design Improvement of Four-Strand Continuous-Casting Tundish Using Physical and Numerical Simulation

Numerical Investigation on Motion and Removal of Inclusions in Continuous Casting Tundish with Multiorifice Filter

Influence of Ladle Exchange on Inclusions in Transition Slabs of Continuous Casting for Automotive Exposed Panel Steel

Numerical Simulation Study on the Influence of Tundish Filter on Molten Steel Flow and Inclusions Removal

The Removal of Inclusions with Different Diameters in Tundish by Channel Induction Heating: A Numerical Simulation Study

Simulation Study on the Influence of Different Molten Steel Temperatures on Inclusion Distribution under Dual-Channel Induction-Heating Conditions

Numerical Simulation of Transient Flow and Heat Transfer in a Steel Ladle During Holding Period

Numerical simulation on the multiphase flow and reoxidation of the molten steel in a two-strand tundish during ladle change

Experimental and Simulation Analysis of Physical Water Model through Tracer Injection under Various Baffles and Turbulence Inhibitor Conditions for Developing the Fluid Flow Parameters and Inclusion Removal Rates in Tundish

Molten Steel Flow, Heat Transfer and Inclusion Distribution in a Single-Strand Continuous Casting Tundish with Induction Heating

Effect of Ladle Shroud Blockage on Flow Dynamics and Cleanliness of Steel in Coupled Ladle–Shroud–Tundish System

Effect of the Tundish Inhibitor Design on the Flotation Efficiency of Nonmetallic Inclusions: Water Modeling and Mathematical Simulations by the Reynolds Stress Model

Water model study on the new designed tundish in Xingcheng special steel

Hydraulic and Numerical Simulation of Flow Field Characteristics in Induction Heating Continuous Casting Tundish

Flow Characteristics for Two-Strand Tundish in Continuous Slab Casting Using PIV

ESTABLISHMENT OF A FULL SCALE TUNDISH PHYSICAL SIMULATION PLATFORM AND APPLICATION RESEARCH

Numerical investigation of bubble behavior and multiphase flow in ladle using purging plug with inclined slit designs