Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Effect of melting temperatures on the orientation and rheology of polyacrylate/silica (PAcr/SiO2) composite microspheres in twin‐screw extruder

Thermal Degradation and Flammability of Nanocomposites Composed of Silica Cross-Linked to Poly(Methyl Methacrylate)

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Effect of Trimethylolpropane Triacrylate Cross-Linkages on the Thermal Stability and Char Yield of Poly (methyl Methacrylate) Nanocomposites

Isothermal crystallization of polypropylene/surface modified silica nanocomposites

Tailoring the crystallization and melting behavior of 3D protein-polymer biocomposite materials: A study of pressure-induced silk fibroin/poly(L-lactic acid) foams

Covalently integrated silica nanoparticles in poly(ethylene glycol)-based acrylate resins: thermomechanical, swelling, and morphological behavior

Effect of processing parameters on degree of crystallinity and mechanical performance of CF/PEKK aerospace composites

Influence of Phase Separation on Mechanical and Anti-Uv Aging Properties of Polyvinylidene Fluoride/Polymethyl Methacrylate Blends

Effects of glass fiber reinforcing and thermal post‐treatment on the mechanical properties and crystallization behaviors of polyoxymethylene

Segmental Dynamics and Rheology of Miscible Poly(vinylidene Fluoride)/poly(methyl Methacrylate) (70/30 by Weight) Blend Filled with Titania or Poly(methyl Methacrylate)-Grafted Titania

Filler Effects on the Phase Separation Behavior of Poly (methyl Methacrylate)/poly (Styrene-Co-acrylonitrile) Binary Polymer Blends

Effect of Mesoscopic Fillers on the Polymerization Induced Viscoelastic Phase Separation at Near- and Off-Critical Compositions.

Influence of Shearing on Impact Polypropylene Copolymer: Phase Morphology, Thermal and Rheological Behavior

Electrical Conduction and Dynamic Rheology of Multi-Walled Carbon Nanotubes and Hydrophobic Nanosilica-Filled Immiscible Poly(Methylmethacrylate)/Polystyrene Blends

Rational Design of Mesoporous Silica (SBA-15)/PF (Phenolic Resin) Nanocomposites by Tuning the Pore Sizes of Mesoporous Silica

Study on the Overmolding Process of Carbon-Fiber-Reinforced Poly (Aryl Ether Ketone) (PAEK)/Poly (Ether Ether Ketone) (PEEK) Thermoplastic Composites

Effects of thermal process conditions on crystallinity and mechanical properties in material extrusion additive manufacturing of discontinuous carbon fibre reinforced polyphenylene sulphide composites

Stretch-Induced Intermediate Structures and Crystallization of Poly(dimethylsiloxane): the Effect of Filler Content

Morphology Evolution of Miscible Blends Between Crystalline Pa6 and Amorphous Pa6icot

Influence of Ionic Liquid on Glass Transition, Dynamic Rheology, and Thermal Stability of Poly(methyl Methacrylate)/silica Nanocomposites