Abstract:Laser powder bed fusion (LPBF) is now a well-established technique for producing metal components for practical use. By utilizing the geometric flexibility of additive manufacturing (AM), a wide range of possibilities for part optimization using complex lattice-based structures are now available, allowing for performance improvements in various industries. Studies on such lattice structures shows that the shape and size of parts and features have localized effects on residual stresses, cooling rates in melt pools, microstructure, and consequently, the mechanical properties of components. In the present work different TPMS (Gyroid, Diamond and Schwarz) lattice structures of a particular sub-millimetre cell size (700 μm) were manufactured in two separate orientations (0° and 90°) to the build platform. Later, post processing methods like electropolishing (EP) was used on one set of specimens to improve the surface finish of the lattices and remove un-melted and trapped powder particles from the lattice. Heat treatment (HT) was employed on another set to enhance the tensile yield strength. These lattice structures were used to probe the influence of thin features on their manufacturability and further the tensile properties of as-built (AB) and post processed samples. The tensile characteristics of both AB and EP samples were relatively similar, although the EP samples displayed marginally lower yield strength and ultimate tensile strength (UTS) in most instances. The elastic modulus values varied between 7.5 GPa to 11 GPa for lattices constructed at 90° and 0 ° angles, respectively. In general, vertically constructed lattices exhibited superior UTS and percentage elongation compared to their horizontally built counterparts, except in the case of the schwarz lattice. The analysis of fracture surface of different lattice samples revealed a predominantly ductile trans-granular fracture.

Printability, post-processing and mechanical behaviour of sub-millimetre sized SS 17-4PH TPMS lattice structures

Effect of Heat Treatment on Mechanical Properties of 17-4 PH Stainless Steel Gyroid Lattice Structures Manufactured by Selective Laser Melting and a Study on Weight Reduction Methods

Improved light-weighting potential of SS316L triply periodic minimal surface shell lattices by micro laser powder bed fusion

Lattice structures in stainless steel 17-4PH manufactured via selective laser melting (SLM) process: dimensional accuracy, satellites formation, compressive response and printing parameters optimization

Numerical Investigation on the Effect of Residual Stresses on the Effective Mechanical Properties of 3D-Printed TPMS Lattices

Topological and Mechanical Properties of Different Lattice Structures Based on Additive Manufacturing

Effect of varying unit cell size on energy absorption behaviour of additive manufactured TPMS PETG lattice structure

Effects of a modified heat treatment on the quasi-static and dynamic behavior of additively manufactured lattice structures

Additively manufactured β-Ti5553 with laser powder bed fusion: microstructures and mechanical properties of bulk and lattice parts

Electron beam powder bed fusion of Ti-6Al-2Sn-4Zr-2Mo lattice structures: morphometrical and mechanical characterisations

Achieving Triply Periodic Minimal Surface Thin-Walled Structures by Micro Laser Powder Bed Fusion Process

Laser Powder Bed Fusion for the Fabrication of Triply Periodic Minimal Surface Lattice Structures: Synergistic Macroscopic and Microscopic Optimization

Effect of microstructural evolution during melt pool formation on nano-mechanical properties in LPBF based SS316L parts

Finite element analysis of the mechanical properties of sheet- and skeleton-gyroid Ti6Al4V structures produced by laser powder bed fusion

A Novel Form "Bubble Microstructure" in LPBF and Investigation of Its Mechanical Strength on TPMS-Gyroid

Phase Transformation Behavior of NiTi Triply Periodic Minimal Surface Lattices Fabricated by Laser Powder Bed Fusion

The Beneficial Effect of a TPMS-Based Fillet Shape on the Mechanical Strength of Metal Cubic Lattice Structures

A Manufacturability Evaluation of Complex Architectures by Laser Powder Bed Fusion Additive Manufacturing

Experimental Investigation on Novel Lattice Structure Parts of IN718 Made by Laser Powder Bed Fusion for Enhanced Specific Flexural Strength

Electron beam powder bed fusion additive manufacturing of Ti6Al4V alloy lattice structures: orientation-dependent compressive strength and fracture behavior

Effect of heat treatment on the properties of D and G lattice structures with different cell sizes fabricated by SLM