Abstract:Porous biomaterials based on triply periodic minimal surfaces (TPMS) are intensely studied and discussed in the literature. Manufacturing of these structures with a complex geometry became possible using additive manufacturing methods, having their own specifics and challenges. Previously, we demonstrated that sheet-based gyroids, one of TPMS structures, manufactured by electron beam powder bed fusion in Melt and Wafer themes could possess identical mechanical properties (quasi-elastic gradient). In the current research sheet-based gyroids were produced using Wafer Theme with five different settings, including electron beam current and scan speed variation with MultiBeam turned on and off, in attempt to obtain thin walls without losing mechanical performance. Mechanical tests revealed that the specimens manufactured with higher beam line energy on average show better mechanical properties. The specimens produced with MultiBeam showed slightly lower mechanical properties, and do not demonstrate significant improvement in the TPMS surface roughness. According to SEM studies, the average wall thickness was about 0.4 mm for specimens with high line energy, and 0.3 mm for low line energy. Through-hole defects on the horizontal surfaces, noticed and discussed by us previously, have larger average area of the hole and more irregular shape for increased beam line energy. TPMS surface morphology of the specimens produced with higher beam energy and no MultiBeam was on average more even. According to EBSD, α/α` martensite with laths oriented in a Widmanstätten basket-weave pattern was observed with no β phase in the resulting material. No significant differences in microstructure between specimens produced with different beam energy was detected. FEA modeling revealed the impact of the wall thickness, through holes size and orientation on quasi-elastic gradient of a gyroid. It was demonstrated that, through holes with small size located on the horizontal surfaces (layer plane) have only a minor impact on the mechanical properties of the samples if they are not extremely abundant.

A Novel Form "Bubble Microstructure" in LPBF and Investigation of Its Mechanical Strength on TPMS-Gyroid

Investigation of the Effect of Artificial Internal Defects on the Tensile Behavior of Laser Powder Bed Fusion 17–4 Stainless Steel Samples: Simultaneous Tensile Testing and X-Ray Computed Tomography

Printability, post-processing and mechanical behaviour of sub-millimetre sized SS 17-4PH TPMS lattice structures

Finite element analysis of the mechanical properties of sheet- and skeleton-gyroid Ti6Al4V structures produced by laser powder bed fusion

Innovative Fabrication Design for In Situ Martensite Decomposition and Enhanced Mechanical Properties in Laser Powder Bed Fused Ti6Al4V Alloy

Microstructure Tailoring for High Strength Ti-6Al-4V without Alloying Elements through Optimized Preheating and Post-Heating Laser Scanning in Laser Powder Bed Fusion

The Influence of the Structure Parameters on the Mechanical Properties of Cylindrically Mapped Gyroid TPMS Fabricated by Selective Laser Melting with 316L Stainless Steel Powder

Advanced Support Structures in Metal Additive Manufacturing: A Comparative Analysis of Porous Media for Enhanced Part Quality and Removal Efficiency

Laser Powder Bed Fusion of Titanium Aluminides: An Investigation on Site-Specific Microstructure Evolution Mechanism

Effect of microstructural evolution during melt pool formation on nano-mechanical properties in LPBF based SS316L parts

Improved light-weighting potential of SS316L triply periodic minimal surface shell lattices by micro laser powder bed fusion

Expanding manufacturability of sheet-based triply periodic minimal surfaces by electron beam powder bed fusion in Wafer theme

Laser powder bed fusion additive manufacturing (LPBF-AM): the influence of design features and LPBF variables on surface topography and effect on fatigue properties

Influence of Contour Scan Variation on Surface, Bulk and Mechanical Properties of LPBF-Processed AlSi7Mg0.6

Quantification of Interdependent Dynamics during Laser Additive Manufacturing Using X‐Ray Imaging Informed Multi‐Physics and Multiphase Simulation

Machine-Learning Assisted Laser Powder Bed Fusion Process Optimization for AlSi10mg: New Microstructure Description Indices and Fracture Mechanisms

Influence of the post-processing operations on surface integrity of metal components produced by laser powder bed fusion additive manufacturing: a review

Investigation of Energy Absorbing Characteristics and Damage Mechanisms of Triply Periodic Minimal Surface Structures fabricated by Powder Bed Fusion Technology

Structural Characterization and Strength Assessment of Laser Powder Bed Fusion Manufactured CM247LC Nickel Based Super Alloy

A Micro-Computed Tomography Comparison of the Porosity in Additively Fabricated CuCr1 Alloy Parts Using Virgin and Surface-Modified Powders

The interplay of local chemistry and plasticity in controlling microstructure formation during laser powder bed fusion of metals