Abstract:Polyether ether ketone (PEEK) is introduced as a material for the additive manufacturing process called fused filament fabrication (FFF), as opposed to selective laser sintering (SLS) manufacturing. FFF manufacturing has several advantages over SLS manufacturing, including lower initial machine purchases costs, ease of use (spool of filament material vs powder material), reduced risk of material contamination and/or degradation, and safety for the users of the equipment. PEEK is an excellent candidate for FFF due to its low moisture absorption as opposed to other common FFF materials, such as Acrylonitrile Butadiene Styrene (ABS). PEEK has been processed into a filament and samples have been manufactured using several build orientations and extrusion paths. The samples were used to conduct tensile, compression, flexural, and impact testing to determine mechanical strength characteristics such as yield strength, modulus of elasticity, ultimate tensile strength and maximum elongation, etc. All tests were conducted at room temperature. A microscope analysis was also conducted to show features on the failures surfaces. The mechanical property results from this study are compared to other published results using traditional thermo-plastic manufacturing techniques, such injection molding. Tensile testing was conducted at three raster orientations, 0°, 90° and alternating between 0° and 90°. Average ultimate tensile stresses were determined to be 73 MPa for 0° orientation, and 54 MPa for 90° orientation, with alternating 0°/90° orientations of 66.5 MPa. Compression testing was conducted at two raster orientations, 0° and alternating between 0° and 90°. Average ultimate strength for the single orientation direction was 80.9 MPa with the alternating orientations at 72.8 MPa. Flexural testing was conducted at three raster orientations, 0°, 90° and alternating between 0° and 90°. Ultimate flexural stress was determined to be 111.7 MPa for 0°, 79.7 MPa for 90°, and 95.3 MPa for orientations alternating between 0° and 90°. Finally, impact testing was conducted at three raster orientations, 0°, 90° and alternating between 0° and 90°. Average impact energy absorbed was determined to be 17.5 Nm in the 0° orientation, 1.4 Nm in the 90° orientation, and 0.7 Nm for the alternating 0° and 90° orientations.

Preparation and characterization of poly(ether ether ketone)/poly(ether imide) [PEEK/PEI] blends for fused filament fabrication

High-Performance Polymer Blends: Manufacturing of Polyetherimide (PEI)–Polycarbonate (PC)-Based Filaments for 3D Printing

An experimental investigation on the tensile properties of PEEK-PEI sandwich structures prepared via fused filament fabrication

Increasing the Isotropy of 3D Printed Poly(ether ether ketone) Using a Combination of Bimodal Polymer Blends and Post-Process Thermal Annealing

Mechanical Properties of Additively Manufactured PEEK Components Using Fused Filament Fabrication

An overview on the influence of process parameters through the characteristic of 3D-printed PEEK and PEI parts

Mechanical characterization of PEEK-CF/PEEK sandwich structures prepared via a combination of fused filament fabrication and epoxy post-bonding

Influence of Polyether Ether Ketone (PEEK) Viscosity on Interlayer Shear Strength in Screw Extrusion Additive Manufacturing

Material Extrusion 3D Printing of PEEK-Based Composites

Effects of processing parameters and annealing on the mechanical properties of polyether ether ketone(PEEK) via fused deposition modeling(FDM)

Tensile and Bending Strength Improvements in PEEK Parts Using Fused Deposition Modelling 3D Printing Considering Multi-Factor Coupling

Preparation of short CF/GF reinforced PEEK composite filaments and their comprehensive properties evaluation for FDM-3D printing

EFFECTS OF EXTRUSION RATE AND POST-ANNEALING ON MECHANICAL PROPERTIES AND PRINTING QUALITY OF ADDITIVELY MANUFACTURED CARBON FIBER REINFORCED POLYETHERKETONEKETONE (PEEK) PARTS

Fused Filament Fabrication of Slow-Crystallizing Polyaryletherketones: Crystallinity and Mechanical Properties Linked to Processing and Post-Treatment Parameters

In-house processing of 3D printable polyetheretherketone (PEEK) filaments and the effect of fused deposition modeling parameters on 3D-printed PEEK structures

Optimization of fused deposition modeling process parameters using the Taguchi method to improve the tensile properties of 3D-printed polyether ether ketone

Mechanical Properties Optimization of Poly-Ether-Ether-Ketone Via Fused Deposition Modeling.

Effect of in Situ Thermal Treatment on Interlayer Adhesion of 3D Printed Polyetherimide (PEI) Parts Produced by Fused Deposition Modeling (FDM)

In-house processing of carbon fiber-reinforced polyetheretherketone (CFR-PEEK) 3D printable filaments and fused filament fabrication-3D printing of CFR-PEEK parts

Effects of 3D Printing Parameters on the Flexural Properties of Semi-Crystalline PEKK

Effect of annealing treatment and infill percentage on 3D-printed PEEK samples by Fused Filament Fabrication