Abstract:This study systematically investigates the influence of the composite addition of Ce, La, and Ca elements on the microstructure evolution and mechanical properties of Mg-3Zn-1Mn/Sn (wt.%) alloys. It indicates that the strength of Mg-Zn-Mn series alloys is superior to that of Mg-Zn-Sn series alloys, due to the stronger restriction of nanosized Mn particles on the recrystallization process and grain growth compared with Mg2Sn phases. The addition of the Ca-La-Ce elements significantly enhances the strength of the Mg-3Zn-1Sn alloy (YS increased by approximately 92.5%, UTS increased by approximately 29.2%, and EL decreased by nearly 52.2%), while for the Mg-3Zn-1Mn alloy, a balanced effect on both the strength and performance can be achieved. This difference mainly lies in the more pronounced refined effect on the grain size and the formation of a bimodal grain structure with strip-like un-DRXed grains and surrounding fine DRXed grains for the Mg-3Zn-1Sn alloy. In contrast, the addition of the Ca-La-Ce elements has a less obvious hindrance on the recrystallization process in the Mg-Zn-Mn series alloy, while significantly weakening the extrusion texture while refining the grains. Through in-depth characterization and experimental analysis, it is found that Sn and Ca can promote the formation of brittle and fine secondary phases. A nanoscale Sn phase (Mg2Sn phase) is more likely to accumulate at the grain boundaries, and the size of the nanoscale Ca2Mg6Zn3 in Mg-Zn-Mn series alloys is finer and more dispersed than that in Mg-Zn-Sn series alloys, thus strongly hindering recrystallization and refining the recrystallized structure of the alloy.

Development and characterization of novel Mg-6Zn-0.6Si- x Sn alloys with varying Sn addition

Influence of Si Addition on the Microstructure and Mechanical Behaviour of Mg-5Sn-3Zn-1Mn Alloy

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Improvement of mechanical properties of hot extruded and age treated Mg–Zn–Mn–Ca alloy through Sn addition

Microstructure, Mechanical Properties and First Principle Calculation of Mg-7Al (-2Sn) Alloys Prepared by Vacuum Die-casting

Comparative Study on Mechanical Properties and Microstructure Evolution of Mg-3Zn-1Mn/Sn Alloy through Ca-La-Ce Addition

Microstructure, Tensile Properties, and Corrosion Behavior of Die-Cast Mg-7Al-1Ca- X Sn Alloys

Analysis of the microstructural evolution and solidification behaviour of Sn-9 wt% Zn alloy with small additions of Mg

Effect of Sn Addition on the Microstructure and Mechanical Properties of AZ31 Alloys

Solidification Microstructure and Mechanical Properties of Cast Magnesium-Aluminum-Tin Alloys

Effect of Ca addition on microstructure and mechanical properties of Mg–3.8Al–1.1Sn alloys

Improving the Mechanical Properties and Intergranular Corrosion Resistance of Al-9.2Mg-0.8Mn-0.2Zr Alloy by Sn Addition

Effects of Zn Addition on the Microstructure, Tensile Properties and Formability of As-Extruded Mg-1Sn-0.5Ca Alloy

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

Effect of Mg2sn Intermetallic on the Grain Refinement in As-Cast Am Series Alloy

Microstructure and Tensile Properties of the Mg-6Zn-4Al-xSn Die Cast Magnesium Alloy

Enhanced Mechanical Properties and Isotropy of Mg-2Al-0.8Sn Alloy through Ca Addition

Effect of Sn content on microstructure and tensile properties of as-cast and as-extruded Mg−8Li−3Al−(1,2,3)Sn alloys

The role of Sn element on the deformation mechanism and precipitation behavior of the Al–Cu–Mg alloy

The Effects of Silicon Addition on the Microstructure and Mechanical Properties of a Mg-Al-Sn Alloy Produced by Vacuum Assisted High Pressure Die Casting

Effect of Minor Gd Addition on Microstructure Evolution and Properties of As-cast Mg-8Zn-1Mn-3Sn Alloy