Abstract:The impact of minor Mg addition on microstructure and mechanical properties of cast Al–Li–Cu–Zr alloy with high lithium content (3 wt % Li) were studied to understand a qualitative assessment of sequence and kinetics of multiple precipitations and its effect on mechanical properties. Scanning Electron Microscope and X-ray diffraction results suggested that raising the content of Mg gradually altered the grain structure of the as-cast alloys and increased the types and volume fraction of the grain boundary intermetallic phase. Unusually, solvus temperature is higher than solidus temperature in 0.5 Mg alloy (Al–3Li–2Cu-0.5Mg-0.15Zr, wt. %), resulting in the incipient melting of the matrix before the complete dissolution of the intermetallic phases. Prominent enhancements in both age-hardening and precipitation kinetics of the base alloy with the addition of Mg were also easily identified, indicating the important role of Mg during isothermal aging. Transmission Electron Microscope and atom probe tomography results showed that minor Mg addition (0.2 wt %, denoted by 0.2 Mg alloy) could encourage the diffusion of Cu atoms by the aggregation of Mg–Cu-vacancy co-clusters, thereby promoting the nucleation of the T1-Al2CuLi and θ′-Al2Cu precipitates. In addition, S′-Al2CuMg precipitate was therefore introduced as a result of Mg addition. With further increasing the content of Mg to 0.5 wt %, the nucleation and growth of S′ precipitate would be promoted at the expense of T1 and θ′ precipitates, especially the latter. Based on the theoretical models and regression analysis, the formation mechanism of δ′-Al3Li precipitate-free-zones gradually changed from the initial vacancy-depletion mechanism to the solute-depletion mechanism, and Mg element could significantly inhibit the coarsening of δ′ precipitate-free-zones. The best balance between ductility and strength was obtained by 0.2 Mg alloy aged for 32 h, and the alloys have significant advantages in terms of density (2.437 g/cm3) and elastic modulus (82.65 GPa) over conventional cast aluminum alloys (density: 2.7–2.8 g/cm3; elastic modulus: 72 GPa).

Analysis of the microstructural evolution and solidification behaviour of Sn-9 wt% Zn alloy with small additions of Mg

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Improving the Mechanical Properties and Intergranular Corrosion Resistance of Al-9.2Mg-0.8Mn-0.2Zr Alloy by Sn Addition

Development and characterization of novel Mg-6Zn-0.6Si- x Sn alloys with varying Sn addition

Influence of Si Addition on the Microstructure and Mechanical Behaviour of Mg-5Sn-3Zn-1Mn Alloy

Effects of Sn and Mn Addition on the Microstructure and Mechanical Properties of As-Extruded Mg–2Al–1Zn Alloys

Solidification Microstructure and Mechanical Properties of Cast Magnesium-Aluminum-Tin Alloys

Influences of Mg content on the microstructures and mechanical properties of cast Al–2Li–2Cu–0.2Zr alloy

Effects of Zn Addition on the Microstructure, Tensile Properties and Formability of As-Extruded Mg-1Sn-0.5Ca Alloy

Effect of Sn Addition on the Microstructure and Mechanical Properties of AZ31 Alloys

Effect of Zn Addition on Microstructure and Mechanical Properties of Mg–9Gd–3Y–0.5Zr Alloy

Hot Tearing Behavior of Mg-4Zn-xSn-0.6Zr Alloys

Comparative Study on Mechanical Properties and Microstructure Evolution of Mg-3Zn-1Mn/Sn Alloy through Ca-La-Ce Addition

Microstructure and Tensile Properties of the Mg-6Zn-4Al-xSn Die Cast Magnesium Alloy

Significant roles of minor Mg addition in microstructural evolution and mechanical properties of cast Al–3Li–2Cu-0.15Zr alloy

Selective Laser Melting of Mg-Zn Binary Alloys: Effects of Zn Content on Densification Behavior, Microstructure, and Mechanical Property

Effect of Zn Addition on the Microstructure and Mechanical Properties of Cast Mg–10Gd–3.5Er– X Zn–0.5Zr Alloys

Effects of Mn Addition on the Microstructure and Mechanical Properties of Cast Mg–9Al–2Sn (wt.%) Alloy

Study on the Microstructure of Mg-4Zn-4Sn-1Mn-xAl As-Cast Alloys

Effect of Minor Gd Addition on Microstructure Evolution and Properties of As-cast Mg-8Zn-1Mn-3Sn Alloy

Enhancement of Hardening and Thermal Resistance of Mg–Sn-based Alloys by Addition of Cu and Al