Abstract:β‐poly(1,1‐difluoroethylene) as a ferroelectric polymer dipole is introduced into Sn–Pb perovskite to enhance the built‐in electric field and promote the charge transfer at perovskite/electron transport layer interface, which effectively suppresses non‐radiative recombination and reduces the interfacial quasi‐Fermi Level Splitting deficit. The resultant Sn–Pb perovskite solar cells achieve a champion efficiency of 23.44%, along with enhanced long‐term stability. The quasi‐Fermi level splitting (QFLS) deficit caused by the non‐radiative recombination at the interface of perovskite/electron transport layer (ETL) can lead to severe open‐circuit voltage (VOC) loss and thus decreases the efficiency of perovskite solar cells (PSCs), however, has received limited attention in inverted tin‐lead PSCs. Herein, the strategy of constructing an extra‐electric field is presented by introducing ferroelectric polymer dipoles (FPD)‐β‐poly(1,1‐difluoroethylene)‐to suppress the QFLS deficit. The directional polarization of FPD can enhance the built‐in electric field (BEF) and thus promote the charge transfer at the perovskite/ETL interface, which effectively suppresses non‐radiative recombination. Furthermore, the incorporation of FPD facilitates high‐quality crystallization of perovskite and reduces the surface energetic disorder. Therefore, the QFLS deficit in the perovskite/ETL half‐stacked device is reduced from 62 to 27 meV after incorporating FPD, and the optimized device achieves an efficiency of 23.44% with a high VOC of 0.88 V. Additionally, the addition of FPD increases the activation energy for ion migration, which can reduce the effect of ion migration on the long‐term stability of the device. Consequently, the FPD‐incorporated device retains 88% of the initial efficiency after 1100 h of continuous illumination at the maximum power point (MPP).

Suppression of Nonradiative Recombination by Vacuum‐Assisted Process for Efficient Lead‐Free Tin Perovskite Solar Cells

Suppressing Nonradiative Recombination in Lead–Tin Perovskite Solar Cells through Bulk and Surface Passivation to Reduce Open Circuit Voltage Losses

Suppressing Bulk and Interfacial Recombination Losses in Sn–Pb Perovskites for Efficient Printable Low‐Bandgap Photovoltaic Devices

Suppressing the formation of tin vacancy yields efficient lead-free perovskite solar cells

Reducing the interfacial voltage loss in tin halides perovskite solar cells

Open-Circuit Voltage Deficits in Tin-Based Perovskite Solar Cells

Antioxidation and Energy-Level Alignment for Improving Efficiency and Stability of Hole Transport Layer-Free and Methylammonium-Free Tin–Lead Perovskite Solar Cells

Lead‐Free Tin‐Based Perovskite Solar Cells: Strategies Toward High Performance

Additive treatment yields high-performance lead-free perovskite light-emitting diodes

Over 14% efficiency of highly reproducible Sn perovskite solar cell via defect passivation and morphology repairment

Enhanced Electric Field Minimizing Quasi‐Fermi Level Splitting Deficit for High‐Performance Tin‐Lead Perovskite Solar Cells

Defect Compensation and Lattice Stabilization Enables High Voltage Output in Tin Halide Perovskite Solar Cells

Low-bandgap Mixed Tin–lead Iodide Perovskite with Large Grains for High Performance Solar Cells

Improving Performance of Lead‐Free Formamidinium Tin Triiodide Perovskite Solar Cells by Tin Source Purification

A Soldering Flux Tackles Complex Defects Chemistry in Sn-Pb Perovskite Solar Cells

Electrochemical Reduction and Ion Injection of Annealing‐Free SnO2 for High Performance Perovskite Solar Cells

High‐Stable Lead‐Free Solar Cells Achieved by Surface Reconstruction of Quasi‐2D Tin‐Based Perovskites

Efficient and Stable Mesoporous CsSnI3 Perovskite Solar Cells via Imidazolium‐Based Ionic Liquid Additive

Stable and Efficient Tin-Based Perovskite Solar Cell via Semiconducting–Insulating Structure

Additive Engineering toward High‐Performance Tin Perovskite Solar Cells

Preparation and Stability Strategies of Inverted Tin-Based Perovskite Solar Cells