Abstract:In this work, acrylato(1,10-phenanthroline)bis(2-thenoytrifluoroacetonato) samarium(III) [Sm(TTA)2(AA)(Phen)] [Sm-AAPhen; TTA=4,4,4-trifluoro-1-(2-thienyl)-1,3-butanedione, AA=acrylic acid, Phen=1,10-phenanthroline] has been synthesized for the first time, which combines the good fluorescence property of Sm(TTA)3(Phen) and the reactivity of acrylic acid with radicals. The uncured composites were prepared by adding different amounts of the Sm(TTA)3(Phen) complex and a certain amount of peroxide into hydrogenated acrylonitrile-butadiene rubber (HNBR). The cured composites were prepared by vulcanizing the uncured composites at 160°C under a pressure of 15MPa for 20min. Fourier Transform Infrared (FTIR) spectra show that the intensity of peaks assigned to reactive CC bond decreases after the curing process, verifying that the in-situ reaction (including polymerization and grafting) of Sm-AAPhen initiated by peroxide radicals took place during the cross-linking of the HNBR matrix. Scanning electron microscopy (SEM) and Transmission electron microscopy (TEM) observations show that the dispersion dimension of the cured composite is far finer than that of the uncured composite. Wide-angle X-ray diffraction (WAXD) testing shows that the crystallinity of Sm-AAPhen in the composites was absent dramatically after the curing process, implying that most of crystalline Sm-AAPhen complex took part in the in-situ reaction and formed the non-crystalline poly(Sm-AAPhen). The dispersion phase of cured Sm-AAPhen/HNBR composites is composed of completely almost nanometer-sized poly(Sm-AAPhen) and few residual Sm-AAPhen particles with significantly reduced dimensions. The fluorescent intensity, lifetime and quantum yields of the cured composite are much higher than that of the uncured one with the same Sm-AAPhen content due to the in-situ reaction.

Curing and post-curing luminescence in an epoxy resin

Study on Co-curing Behavior and their Laminate Properties of Low Bromined Epoxy/Cyanate Blends

Synthesis and Curing of a Novel Combined Liquid Crystalline Epoxy

Fluorescence Enhancement Induced by Curing Reaction in Nanostructured Epoxy Thermosets Containing a Diblock Copolymer

Study of Property of Visible Light Curable Resin

Photoluminescence enhancement from the defects state formed by neutron/gamma mixed irradiation in an epoxy resin for LED applications

Monitoring the Curing Process of Epoxy Resin Nanocomposites Based on Organo-Montmorillonite – a New Application of Resin Curemeter

Evolutions of Surface Characteristics and Electrical Properties of the Fluorinated Epoxy Resin During Ultraviolet Irradiation

Γ-Ray Radiation Curing Behavior of Multi-walled Carbon Nanotubes-Epoxy Nanocomposites

Influence of In-Situ Reaction on Luminescent Properties of Samarium-Complex/hydrogenated Acrylonitrile-Butadiene Composites

Curing Behaviour of Epoxy Resin/Graphite Composites Containing Ionic Liquid

Curing reactions, reaction kinetics, and latency of epoxy resin cured with L‐tryptophan and L‐tyrosine

In Situ Monitoring of the Curing of a Bisphenol-A Epoxy Resin by Raman-Spectroscopy and Rheology

Comparative study on the curing kinetics and mechanism of a lignin-based-epoxy/anhydride resin system

Study On The Post-Cure Kinetics Of Epoxy Resin Irradiated By An Electron Beam

Photoluminescent epoxy microspheres: preparation, surface functionalization via grafting polymerization and photophysical properties

Synthesis of epoxy–clay nanocomposites. Influence of the nature of the curing agent on structure

Cure kinetics, glass transition temperature development, and dielectric spectroscopy of a low temperature cure epoxy/amine system

Curing study of epoxy resin by new aromatic amine functional curing agents along with mechanical and thermal evaluation

A novel environmentally friendly and biocompatible curing agent for lead-free electronics

Self-extinguishing and transparent epoxy resin modified by a phosphine oxide-containing bio-based derivative