Abstract:This paper describes the dynamic behaviour of a roller chain drive. A mechanical model of the chain and all other parts of the drive is presented. For a detailed analysis of the forces and the contact configuration each link, sprocket, shaft, and guide is treated as a separate body. All these bodies are specified with their exact contour. In order to verify the model a test bench has been built where all major excitations and replies of the system are measured. A method to measure chain forces is shown. A comparison between measurement and simulation for some results is given. INTRODUCTION In combustion engines either roller chain drives, belt drives or geared drives are used to set the cam shaft and accessory aggregates going. The characteristic features of roller chains are high solidity, stiffness, temperature stability and a long working life, while belts are known to break unscheduled. Every chain drive can consist of several single chain drives, which again consists of sprockets, pulleys, one-sided and two-sided guides, a tension device and chain strands. Because of the large relative velocity not well designed drives suffer from high wear and ground noise. Moreover it affects the cyclic irregularity of the crank shaft and cam shaft, which again influences the gas exchange of the engine. GROESEL [7] and other authors studied the variation in speed and acceleration of a sprocket due to the polygonal effect. The basic work on natural frequencies of a chain span has been done by BINDER [I] and RACHNER[11] modeling the span as a series of rigid bodies, Among others FRITZER [3] researched the behaviour of the strands, modeled as a uniform string. NAKANISHIand SHABANA[9]developed a very detailed chain model for large-scale tracked vehicles, regarding links, sprockets and dampers as separate bodies. Seyfferth (1992), Pfeiffer and Glocker (1993) did the basic work on multi-body systems with variant structure. They appointed a valid contact configuration and calculated the contact forces in this case. The impact equations for such systems are derived in Pfeiffer (1984) and Glocker and Pfeiffer (1995). In this investigation all links are modeled as separate rigid bodies connected by revolute joints. Contacts to the sprockets are described by nonlinear force laws, regarding the exact tooth contour. The model properties of all components of a roller chain drive are shown and the method to measure chain forces is displayed. The simulation results for a BMW 318 combustion engine will be compared with the corresponding measurement.

FIFTH INTERNATIONAL CONGRESS ON SOUND AND VIBRATION DECEMBER15-18, 1997 ADELAIDE, SOUTH AUSTRALIA

Modeling and Simulation of Torsional Vibration of the Compliant Sprocket in Balance Chain Drive Systems

MODELING AND SIMULATION OF THE CHAIN-SPROCKET SYSTEM WITH MULTI RIGID BODY METHOD

Study on the New Roller Chain Drive Tooth Profile and Its Dynamic Characteristics

A New Basis for the Rating of Roller-Chain Drives

Simulation Research on Dynamic Characteristic of Timing Chain Trains of Gasoline Engine

Planar dynamic modelling of round link chain drives considering the irregular polygonal action and guide rail

THE DYNAMIC MODELLING OF A SPUR GEAR IN MESH INCLUDING FRICTION AND A CRACK

Dynamics of Drive Axle System with Effects of Input Torque

Simulation Study on Dynamic Characteristics of the Chain Drive System for Mining Scraper Conveyor Driven by the Permanent Magnet Synchronous Motor

Mathematical Modeling and Simulation of Real Time Transmission of Polygon Effect on Chain Drive

A harmonic drive model considering geometry and internal interaction

Fatigue life analysis of scraper conveyor chain ring under different chain speeds and loads

Modeling of the electric drive of the main motion of the rolling cage as a multi-mass electromechanical system

Dynamic analysis of a selected passenger car belt transmission with the GMS friction model

Dynamic Performance Research and Design Optimization of Gasoline Engine Timing Sprocket

Preliminary modelling of power losses in roller chain drive: application to single speed cycling

The consequence of performance increases of automotive engines on the modelisation of main and connecting-rod bearings

Evaluation of Model-based Control of Reaction Forces at the Supports of Large-size Crankshafts

AN EFFICIENT CRANKSHAFT DYNAMIC ANALYSIS USING SUBSTRUCTURING WITH RITZ VECTORS

Dynamic behavior of a power re-circulating gear test rig including periodic variation of mesh stiffness and static transmission error