Abstract:This paper describes the dynamic behaviour of a roller chain drive. A mechanical model of the chain and all other parts of the drive is presented. For a detailed analysis of the forces and the contact configuration each link, sprocket, shaft, and guide is treated as a separate body. All these bodies are specified with their exact contour. In order to verify the model a test bench has been built where all major excitations and replies of the system are measured. A method to measure chain forces is shown. A comparison between measurement and simulation for some results is given. INTRODUCTION In combustion engines either roller chain drives, belt drives or geared drives are used to set the cam shaft and accessory aggregates going. The characteristic features of roller chains are high solidity, stiffness, temperature stability and a long working life, while belts are known to break unscheduled. Every chain drive can consist of several single chain drives, which again consists of sprockets, pulleys, one-sided and two-sided guides, a tension device and chain strands. Because of the large relative velocity not well designed drives suffer from high wear and ground noise. Moreover it affects the cyclic irregularity of the crank shaft and cam shaft, which again influences the gas exchange of the engine. GROESEL [7] and other authors studied the variation in speed and acceleration of a sprocket due to the polygonal effect. The basic work on natural frequencies of a chain span has been done by BINDER [I] and RACHNER[11] modeling the span as a series of rigid bodies, Among others FRITZER [3] researched the behaviour of the strands, modeled as a uniform string. NAKANISHIand SHABANA[9]developed a very detailed chain model for large-scale tracked vehicles, regarding links, sprockets and dampers as separate bodies. Seyfferth (1992), Pfeiffer and Glocker (1993) did the basic work on multi-body systems with variant structure. They appointed a valid contact configuration and calculated the contact forces in this case. The impact equations for such systems are derived in Pfeiffer (1984) and Glocker and Pfeiffer (1995). In this investigation all links are modeled as separate rigid bodies connected by revolute joints. Contacts to the sprockets are described by nonlinear force laws, regarding the exact tooth contour. The model properties of all components of a roller chain drive are shown and the method to measure chain forces is displayed. The simulation results for a BMW 318 combustion engine will be compared with the corresponding measurement.

MODELING AND SIMULATION OF THE CHAIN-SPROCKET SYSTEM WITH MULTI RIGID BODY METHOD

Modeling and Simulation of Torsional Vibration of the Compliant Sprocket in Balance Chain Drive Systems

Analysis and Simulation on Dynamic Stress of Tracked Vehicle Sprocket Based on Rigid-Flexible Coupling

Mathematical Modeling and Simulation of Real Time Transmission of Polygon Effect on Chain Drive

FIFTH INTERNATIONAL CONGRESS ON SOUND AND VIBRATION DECEMBER15-18, 1997 ADELAIDE, SOUTH AUSTRALIA

Rigid-flexible coupled modeling of compound multistage gear system considering flexibility of shaft and gear elastic deformation

Modeling and Analysis of Gear-Shifting Process of Motor-Transmission Coupled Drive System

Hybrid Dynamic Modeling and Analysis of High-Speed Thin-Rimmed Gears

Nonlinear dynamics of a spur gear pair with force-dependent mesh stiffness

Planar dynamic modelling of round link chain drives considering the irregular polygonal action and guide rail

Dynamic Performance Research and Design Optimization of Gasoline Engine Timing Sprocket

Dynamic Modeling and Analysis of Nonlinear Compound Planetary System

Dynamic Analysis of a Spur Geared Rotor-Bearing System with Nonlinear Gear Mesh Stiffness

Research on multi-body dynamic model of automatic discrete system for protection bearing without cage

Nonlinear dynamic response of a spur gear pair based on the modeling of periodic mesh stiffness and static transmission error

Dynamics research and chaos identification of rigid-flexible coupling multi-link mechanism with irregular wear clearances

A novel dynamic modeling method with slice coupling for thin-rimmed gear transmission

Modeling and Analysis of Engaging Process of Automated Mechanical Transmissions

Dynamic Behavior Analysis of Spur Gears with Constant & Variable Excitations Considering Sliding Friction Influence

Dynamic Modeling and Simulation of Double-Planetary Gearbox Based on Bond Graph

Dynamic modeling of the gear-rotor systems with spatial propagation crack and complicated foundation structure