Abstract:High temperature titanium alloys are being urgently developed owing to the requirements of advanced aerospace industry. Performance of the alloys in service under high-temperature environments always attracts great attention. In this study, variations of microstructure and mechanical property in TC25 (Ti-6.5Al-2Mo-1Zr-1Sn-1 W-0.2Si) dual-phase high temperature titanium alloy subjected to thermal exposure have been systematically investigated by coupling microstructural characterization, compositional analyses and mechanical measurement. It is found that strength is significantly enhanced while ductility is sharply degraded when the alloy is thermally exposed at 550 degrees C for a long duration of 100 h. Microstructural observations manifest that ternary alpha-needles (alpha t) are drastically precipitated from beta-ligaments inside transformed beta-matrix (beta trans) whilst alpha 2 (Ti3Al)-phase is produced from primary alpha-phase (alpha p) through ordered transformation. The precipitation of alpha t-needles is promoted by beta-phase metastability resulting from insufficient element partitioning in the initial microstructure. The beta-phase stability also renders alpha t-precipitation encounter size effect of beta-ligaments, where the precipitation is suppressed when beta-ligaments are thin in size. Both precipitation of alpha t-needles and alpha 2-phase triggers precipitation-hardening effect, which results in strain localization and thereby regresses alloy ductility. However, further analysis indicates that compared with alpha 2-phase, alpha t-precipitation plays more adverse role in embrittlement in the current alloy. This is different from thermal-exposed behavior of most of high temperature titanium alloys reported in literatures. These findings enrich our fundamental understanding on thermal stability of high temperature titanium alloys, and provide plausible implication to improve high temperature performance via controlling phase precipitation.

Influence of Quenching Temperature on the Structure, Phase Composition, Physical and Mechanical Properties of a High-Strength Titanium Alloy of the Martensitic Class

Formation of Structure, Phase Composition and Properties in a Two-Phase Titanium Alloy Upon Variation of the Temperature and Rate Parameters of Heat Treatment

Formation of the Structure, Phase Composition, and Properties in High-Strength Titanium Alloy upon Isothermal and Thermomechanical Treatment

Effect of Step-quenching on Microstructure and Mechanical Properties of TC21 Titanium Alloy

The Effects Produced by the Rate of Heating on the Aging Temperature on the Structure and Hardening of the Ti–10V–2Fe–3Al Titanium Alloy with Different Carbon Contents

Effect of Temperature and Rate Treatment Parameters on the Structural Phase State and Properties of Ti2AlNb Titanium Aluminide-Based Alloy

Influence of Microstructures on Tensile Properties at 400℃ of TC4 Titanium Alloy

Effects of Different Heat Treatments on Microstructure and Mechanical Properties of TC4-DT Titanium Alloy Bar

Influences of Solution Temperatures on Microstructure and Mechanical Properties of near α Titanium Alloy

Insights into Microstructural Stability and Embrittlement of TC25 High Temperature Titanium Alloy Subjected to Thermal Exposure

The effect of austenitizing temperature upon the microstructure and mechanical properties of experimental Fe/Cr/C steels

The influence of temperature during water-quench rapid heat treatment on the microstructure, mechanical properties and biocompatibility of Ti6Al4V ELI alloy

Toughening of Titanium Alloys by Twinning and Martensite Transformation

Effects of Heat Treatment Conditions on Microstructure and Mechanical Properties of TC11 Titanium Alloy

Microstructural Evolution and Mechanical Properties of TC18 Titanium Alloy with Bimodal Structure

Influences of Quenching Temperature on the Microstructure Evolution and Strength−Toughness of a Novel Medium‐Carbon Ti−Mo‐Bearing Martensite Steel

Influence of Solution Treatment on the Microstructure and Mechanical Property of Ti60 Alloy

Comparative Investigation of the Influence of Ultrafine-Grained State on Deformation and Temperature Behavior and Microstructure Formed during Quasi-Static Tension of Pure Titanium and Ti-45Nb Alloy by Means of Infrared Thermography

Study on the Relationship Between Microstructure and Mechanical Property in a Metastable Β Titanium Alloy

Influence of Heat Treatment on Microstructure and Mechanical Properties of TC4 Titanium Alloy

The effect of heat treatment process on microstructure and mechanical property of large-sized tci8 titanium alloy bar