Abstract:Fill factor (FF) is a determining parameter for the power conversion efficiency (PCE) of organic solar cells (OSC). So far, nonfullerene (NF) OSCs with state-of-the-art PCEs exhibit FFs <0.8, lower than the values of Si or perovskite solar cells. The FFs directly display the dependence of photocurrent on bias, meaning that the competition between charge extraction and recombination is modulated by internal electric potential (Vin). Here, we report a study to understand key parameters/properties affecting the device FF based on seven groups of NF-OSCs consisting of widely used PBDBT-2F or PTB7-Th donors and representative NF-acceptors with FFs ranging from 0.60 to 0.78 and PCEs from 10.27 to 16.09%. We used field-dependent transient photocurrent measurements to reveal that fast and field-insensitive charge extraction at low Vin is an essential prerequisite for obtaining high FFs (0.75–0.8), which is enabled by balanced charge transport in steady and reduced bimolecular charge recombination in high purity phases. With bias-dependent quantum efficiency analysis, we further show that the recombination loss at low Vin in the devices with low FFs tends to be more significant involving excitons generated in the donor phase of blends. Our results provide relevance for how to improve the FF toward the boost of photovoltaic performance in NF-OSCs.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c09123?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c09123</a>.Calculation methods of physical parameters; energy level of materials; EQE spectra; normalized photocurrent decay kinetics; τext versus FF characteristics; TPC and TPV measurements; dark J–V characteristics of single-carrier devices; illumination-dependent open-circuit curves; AFM images; and bias-dependent EQE spectra (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c09123/suppl_file/am0c09123_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Achieving High Fill Factor in Organic Photovoltaic Cells by Tuning Molecular Electrostatic Potential Fluctuation

High fill factor organic solar cells with increased dielectric constant and molecular packing density

14.7% Efficiency Organic Photovoltaic Cells Enabled by Active Materials with a Large Electrostatic Potential Difference

Increasing Molecular Packing Density and Dielectric Constant in Non-Fullerene Acceptors Enables to Boost the Fill Factor Approaching 0.82 in Organic Solar Cells

Fast Field-Insensitive Charge Extraction Enables High Fill Factors in Polymer Solar Cells

A Highly Efficient Non‐Fullerene Organic Solar Cell with a Fill Factor over 0.80 Enabled by a Fine‐Tuned Hole‐Transporting Layer

Rational Tuning of Molecular Interaction and Energy Level Alignment Enables High‐Performance Organic Photovoltaics

Molecular Design of Fully Nonfused Acceptors for Efficient Organic Photovoltaic Cells

Achieving 31% efficiency in organic photovoltaic cells under indoor light using a low energetic disorder polymer donor

Subtle Side Chain Triggers Unexpected Two-Channel Charge Transport Property Enabling 80% Fill Factors and Efficient Thick-Film Organic Photovoltaics

Refined molecular microstructure and optimized carrier management of multicomponent organic photovoltaics toward 19.3% certified efficiency

Medium Bandgap Non‐fullerene Acceptor Enabling Organic Photovoltaic Cell with 30% Efficiency Under Indoor Artificial Light

Enabling low voltage losses and high photocurrent in fullerene-free organic photovoltaics

Optimized Phase Separation and Reduced Geminate Recombination in High Fill Factor Small-Molecule Organic Solar Cells

Iodinated Electron Acceptor with Significantly Extended Exciton Diffusion Length for Efficient Organic Photovoltaic Cells

Quinoxaline-Based Wide Band Gap Polymers for Efficient Nonfullerene Organic Solar Cells with Large Open-Circuit Voltages.

Achieving over 16% Efficiency for Single-Junction Organic Solar Cells

Boosting Fill Factor of Semitransparent Donor‐Poor Organic Solar Cells for the Best Light Utilization Efficiency

Optimization of Charge Extraction and Interconnecting Layers for Highly Efficient Perovskite/Organic Tandem Solar Cells with High Fill Factor

High‐Efficiency and Mechanically Robust All‐Polymer Organic Photovoltaic Cells Enabled by Optimized Fibril Network Morphology

Modulating the deep-level defects and charge extraction for efficient perovskite solar cells with high fill factor over 86%