Abstract:This study presents a colloidal synthesis method to produce thermoelectric Cu3SbSe4 nanocrystals with high yield. Pb doping is employed to increase carrier concentration and effective mass, confirmed by experimental studies and theoretical calculations. Additionally, lattice distortions and other intriguing nanostructures are found to significantly reduce thermal conductivity. Consequently, the thermoelectric figure of merit zT is greatly enhanced. Developing cost‐effective and high‐performance thermoelectric (TE) materials to assemble efficient TE devices presents a multitude of challenges and opportunities. Cu3SbSe4 is a promising p‐type TE material based on relatively earth abundant elements. However, the challenge lies in its poor electrical conductivity. Herein, an efficient and scalable solution‐based approach is developed to synthesize high‐quality Cu3SbSe4 nanocrystals doped with Pb at the Sb site. After ligand displacement and annealing treatments, the dried powders are consolidated into dense pellets, and their TE properties are investigated. Pb doping effectively increases the charge carrier concentration, resulting in a significant increase in electrical conductivity, while the Seebeck coefficients remain consistently high. The calculated band structure shows that Pb doping induces band convergence, thereby increasing the effective mass. Furthermore, the large ionic radius of Pb2+ results in the generation of additional point and plane defects and interphases, dramatically enhancing phonon scattering, which significantly decreases the lattice thermal conductivity at high temperatures. Overall, a maximum figure of merit (zTmax) ≈ 0.85 at 653 K is obtained in Cu3Sb0.97Pb0.03Se4. This represents a 1.6‐fold increase compared to the undoped sample and exceeds most doped Cu3SbSe4‐based materials produced by solid‐state, demonstrating advantages of versatility and cost‐effectiveness using a solution‐based technology.

Heavy elemental compound addition enhancing thermoelectric performance of Chromium Silicide synthesized by Spark plasma sintering

Enhancement of electrical transport properties in CrSi2-NbSi2 composite synthesized by the AM-SPS technique

Lead-free AgSn4SbTe6 Nanocomposites with Enhanced Thermoelectric Properties by SiC Nanodispersion

Impact of Cr content on the thermoelectric properties of the Cr/Sb co-doped Mg2.2−xCrx(Si0.3Sn0.7)0.98Sb0.02 compound

Synergistic Combination of Sb2Si2Te6 Additives for Enhanced Average ZT and Single-Leg Device Efficiency of Bi0.4Sb1.6Te3-based Composites

Reduced thermal conductivity and enhanced TE performance in CrSb2via Fe-Bi co-substitution

Enhanced Thermoelectric Performance of p-Type Mg3- xZnxSb2/Sb Composites: The Role of ZnSb/Sb Composites

Enhanced thermoelectric performance enabled by compositing ZrO2 in n-type SiGe alloy with low thermal conductivity

Enhancing Thermoelectric Performance of AgSbTe 2 -Based Compounds via Microstructure Modulation Combining with Entropy Engineering

Si-Based Materials for Thermoelectric Applications

Thermoelectric Performance Enhancement of (bis)1.2(tis2)2 Misfit Layer Sulfide by Chromium Doping

Distinctive Thermoelectric Properties of Supersaturated Si-Ge-P Compounds: Achieving Figure of Merit ZT > 3.6

Enhanced Thermoelectric Performance of $p$-type BiSbTe Through Incorporation of Magnetic CrSb

Rational design and synthesis of Cr 1-x Te/Ag 2 Te composites for solid-state thermoelectromagnetic cooling near room temperature

Fabrication and Characterization of Thermoelectric CrSi2 Compound by Mechanical Alloying and Spark Plasma Sintering

Boosting thermoelectric performance in Cu3SbS4-based compounds through incorporating SiC nanoparticles

Band Engineering Through Pb‐Doping of Nanocrystal Building Blocks to Enhance Thermoelectric Performance in Cu3SbSe4

Synergetic enhancement of power factor and suppression of lattice thermal conductivity via electronic structure modification and nanostructuring on Ni and B co-doped p-type Si-Ge alloy

Enhancing Thermoelectric Performance of Mg3Sb2 Through Substitutional Doping: Sustainable Energy Solutions via First-Principles Calculations

Composition Optimization of P-Type AgSn M SbTe M +2 Thermoelectric Materials Synthesized by Mechanical Alloying and Spark Plasma Sintering

Improvement of the Thermoelectric Properties of P-Type Mg3Sb2 by Mg-Site Double Substitution